Author Topic: Jetting questions for newb  (Read 2278 times)

0 Members and 1 Guest are viewing this topic.

Offline fraz83

  • Jr. Member
  • **
  • Posts: 44
Jetting questions for newb
« on: July 22, 2011, 08:06:40 AM »
I have had my bike for just over 2 years now and i have never messed with the carb.. i noticed it bogs sometimes at 3/4 throttle when its not warmed up real good .. i ushually ride around 2000 to just over 3000ft .. i have no carb experience really .. im just wondering how hard it is to jet it properly ..

thanks

frazer

Offline kxpegger

  • Hero Member
  • *****
  • Posts: 855
Re: Jetting questions for newb
« Reply #1 on: July 22, 2011, 08:55:50 AM »
PWK39

168 Main
55 Pilot
#7 slide
N82M needle #2
Air screw 1 1/2 turns

I'm in Las Vegas so I usually ride between 2000' and 3000'. Some of my riding is up to 10,000' and this still works without fouling any plugs. At around 4000' I'll start to notice the power dropping off but otherwise the mighty 500 just keeps chugging along!

Here's some jetting charts. The Team Green Chart worked the best for me.

http://www.kxriders.com/forums/index.php/topic,4816.0.html
« Last Edit: July 22, 2011, 08:57:57 AM by kxpegger »
North Las Vegas

"05" RMZ450, "08" KX500AF "11" KTM 450SX-F "12" KTM 250SX "15" KTM450SX-F

Offline fraz83

  • Jr. Member
  • **
  • Posts: 44
Re: Jetting questions for newb
« Reply #2 on: July 22, 2011, 09:01:05 AM »
so just turn the air screw all the way to the left then from there go 1 and a half turns ? and what is n82m needle #2?

Offline fraz83

  • Jr. Member
  • **
  • Posts: 44
Re: Jetting questions for newb
« Reply #3 on: July 22, 2011, 09:23:25 AM »
my bad to the right "from the video i just watched on youtube.."

Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: Jetting questions for newb
« Reply #4 on: July 22, 2011, 01:14:22 PM »
 Yep,
 Just remember GENTLY SEATED position.  Your not gonna hurt anything moving the air screw around so don't worry about blowing anything up...Yet... :-D
       
Move the airscrew about a 1/4 of a turn either direction and take a spin, just like getting a pair of glasses... Better or worse?...
  A general rule is to try and keep your airscrew at about 1 1/2 turns out from gently seated.  That way you can dial it in or out as needed for the riding conditions of the day.     
 
  The N82m Needle is the stock needle alot of KX5's came with from the factory and lot's o guys like to run with.
The next time you have the carb apart, look at the needle just under where the last clip position is.
   That's where you'll find your needle # stamped into.
  Tuck\o/   
"The Truth Has No Agenda"

Offline Polar-Bus

  • Hero Member
  • *****
  • Posts: 1,023
Re: Jetting questions for newb
« Reply #5 on: July 25, 2011, 12:25:58 AM »
I have had my bike for just over 2 years now and i have never messed with the carb.. i noticed it bogs sometimes at 3/4 throttle when its not warmed up real good .. i ushually ride around 2000 to just over 3000ft .. i have no carb experience really .. im just wondering how hard it is to jet it properly ..

thanks

frazer

You really should not be at "3/4" throttle until your engine is thouroghly warmed up, you are asking for a cold seizure...
01' KX500
'84 GPz1100
'87 GSX-R  750
'06 HD Fatboy
'73 Kawi H1
'03 CRG KX500 Shifter kart