« previous next »
Pages: [1]   Go Down

Author Topic: All right, now what?  (Read 6702 times)

0 Members and 3 Guests are viewing this topic.

Offline gwcrim

  • Hero Member
  • *****
  • Posts: 673
    • http://profiles.yahoo.com/gwcrim
All right, now what?
« on: April 06, 2011, 08:26:27 AM »
I now have cases with the swingarm hole bored to accept the 250 sized bolt.  However, they weren't machined on the sides to fit between the swingarm.  I'm thinking that I'll machine the swingarm to fit instead of the cases. 

Does the original width of the 500 engine fit the aluminum framed bikes?

Any input on this decision?
Logged
~Crim~
You raise the blade
You make the change
You rearrange me 'til I'm sane

Offline DoldGuy

  • Hero Member
  • *****
  • Posts: 1,198
Re: All right, now what?
« Reply #1 on: April 06, 2011, 08:50:50 AM »
Quote from: gwcrim on April 06, 2011, 08:26:27 AM
I now have cases with the swingarm hole bored to accept the 250 sized bolt.  However, they weren't machined on the sides to fit between the swingarm.  I'm thinking that I'll machine the swingarm to fit instead of the cases. 

Does the original width of the 500 engine fit the aluminum framed bikes?

Any input on this decision?

Crim,
I dont know about the AF conversion, but Don46 has posted about the Steel Frame that you originally posted about. His post showed the cases being drilled for the pivot bolt but he machined the swingarm bushings (not the engine) & the swingarm to accomodate the K5 motor, which I think is a better solution.
DoldGuy
Logged
Its Never too Late to Have a Happy Childhood!

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: All right, now what?
« Reply #2 on: April 06, 2011, 10:54:34 AM »
+1
I ground the bushings down.
If I can do it, it must be easy...
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Motorrad

  • Guest
Re: All right, now what?
« Reply #3 on: April 06, 2011, 05:32:51 PM »
I think I like that idea much better also.... if you mess up, or decide to change the motor over to anything else in the future. (the new latest greatest frame comming out made of Ground up Unicorn horns, and suspension filled with smashed up pixie juice)... swingarm bushings are cheap vs cases...
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: All right, now what?
« Reply #4 on: April 06, 2011, 05:53:54 PM »
If you have a old pivot pin with a nut, and a bench grinder, then you can do it too  :-D
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline gwcrim

  • Hero Member
  • *****
  • Posts: 673
    • http://profiles.yahoo.com/gwcrim
Re: All right, now what?
« Reply #5 on: April 07, 2011, 12:29:07 AM »
Quote from: sandblaster on April 06, 2011, 05:53:54 PM
If you have a old pivot pin with a nut, and a bench grinder, then you can do it too  :-D

Now that sounds like my kinda work.  Measure with a yardstick, mark it with chalk, cut it with a torch.
Logged
~Crim~
You raise the blade
You make the change
You rearrange me 'til I'm sane

Offline The Flyin Hawaiian

  • Hero Member
  • *****
  • Posts: 597
Re: All right, now what?
« Reply #6 on: April 08, 2011, 03:52:05 PM »
Plenty of space in the swingarm to cut. I did it to mine and it was pretty easy.
Logged
A couple of 03 and 04 KXs, a few YZs, 3 PE 400s, a DR and a TS.

Offline gwcrim

  • Hero Member
  • *****
  • Posts: 673
    • http://profiles.yahoo.com/gwcrim
Re: All right, now what?
« Reply #7 on: April 16, 2011, 04:38:09 AM »
I did some measuring.  Looks like 3/8 per side.  Does that sound right?

Next step is to powder coat the frame and assemble the engine.  Gotta farm out both of those jobs.

Nice to start this project moving again.
Logged
~Crim~
You raise the blade
You make the change
You rearrange me 'til I'm sane

Offline gwcrim

  • Hero Member
  • *****
  • Posts: 673
    • http://profiles.yahoo.com/gwcrim
Re: All right, now what?
« Reply #8 on: April 16, 2011, 04:58:52 AM »
One more question.  The head stay.  Is there anyone on here that makes them anymore?
Logged
~Crim~
You raise the blade
You make the change
You rearrange me 'til I'm sane

Motorrad

  • Guest
Re: All right, now what?
« Reply #9 on: April 16, 2011, 08:06:56 AM »
Quote from: gwcrim on April 16, 2011, 04:58:52 AM
One more question.  The head stay.  Is there anyone on here that makes them anymore?

Doesnt Jerry (Jfab) make one??


Edit:  like this one.  http://www.kxriders.com/forums/index.php/topic,6447.0.html
« Last Edit: April 16, 2011, 08:10:04 AM by Motorrad »
Logged

Motorrad

  • Guest
Re: All right, now what?
« Reply #10 on: April 16, 2011, 06:10:26 PM »
Forgot to add... Calling Jerry on the phone is the best way to get ahold of him... he is a busy guy...   But has the time to ship parts out ASAP... (every time I have delt with him... I have to call him... but my parts are shipped out same or next day)

PM me if you need his phone number.
Logged

Offline gwcrim

  • Hero Member
  • *****
  • Posts: 673
    • http://profiles.yahoo.com/gwcrim
Re: All right, now what?
« Reply #11 on: April 17, 2011, 12:14:41 AM »
Ya please shoot it to me.
Logged
~Crim~
You raise the blade
You make the change
You rearrange me 'til I'm sane
Pages: [1]   Go Up
« previous next »