« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: KIPS BOLT MOD  (Read 27831 times)

0 Members and 4 Guests are viewing this topic.

Offline alexander-vmann

  • Sr. Member
  • ****
  • Posts: 412
Re: KIPS BOLT MOD
« Reply #45 on: November 21, 2015, 03:26:20 AM »
wonder if this could help my bike rev up smoother(especially on higher rpm) how can i tell if the valves are over closing? or should i just get a modded bolt and be safe :-P
Logged
KX 500 newbie

my bike: 1993 kx500

Offline Dutch-K5 Fan

  • Hero Member
  • *****
  • Posts: 759
Re: KIPS BOLT MOD
« Reply #46 on: November 21, 2015, 07:34:38 AM »
Well all 89+ k5 overrotate, because it's done for decompression.
A moded bolt corrects this so te kips is closed at low rpm.

Dutchie
Logged
Proud owner of a KX500AF

Motorrad

  • Guest
Re: KIPS BOLT MOD
« Reply #47 on: November 21, 2015, 05:04:55 PM »
My new sexy stealth TITANIUM kips bolt mod...

Logged

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: KIPS BOLT MOD
« Reply #48 on: November 21, 2015, 05:37:03 PM »
Quote from: Motorrad on November 21, 2015, 05:04:55 PM
My new sexy stealth TITANIUM kips bolt mod...




 :-o So pretty
Logged
"Let there be light"

Offline jBernard

  • Sr. Member
  • ****
  • Posts: 299
Re: KIPS BOLT MOD
« Reply #49 on: November 21, 2015, 06:58:22 PM »
Quote from: Motorrad on November 21, 2015, 05:04:55 PM
My new sexy stealth TITANIUM kips bolt mod...


dang where'd you get that! i was going to get one made up. but getting one off broached was going to cost to much. thought about just putting an 8mm hex head on it but that would make it look not as clean.
Logged
'09 KX500AF - never ending project
'14 KTM 300SX

Motorrad

  • Guest
Re: KIPS BOLT MOD
« Reply #50 on: November 22, 2015, 01:26:04 AM »
Quote from: jBernard on November 21, 2015, 06:58:22 PM
Quote from: Motorrad on November 21, 2015, 05:04:55 PM
My new sexy stealth TITANIUM kips bolt mod...


dang where'd you get that! i was going to get one made up. but getting one off broached was going to cost to much. thought about just putting an 8mm hex head on it but that would make it look not as clean.

Talk to alward25
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: KIPS BOLT MOD
« Reply #51 on: November 22, 2015, 02:56:32 AM »
I stole your picture  :lol:

Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: KIPS BOLT MOD
« Reply #52 on: November 22, 2015, 05:11:10 AM »




Logged
"Let there be light"
Pages: 1 2 3 [4]   Go Up
« previous next »