« previous next »
Pages: [1]   Go Down

Author Topic: BEST K5 CON ROD  (Read 5063 times)

0 Members and 1 Guest are viewing this topic.

Offline jonny500

  • Hero Member
  • *****
  • Posts: 580
BEST K5 CON ROD
« on: October 30, 2010, 07:38:36 AM »
i have heard stories of the k5 breaking con rods. i currently have a bent one. my questions are have any of you guys bent or snapped one, what do you recomend, what do the guys running high compression engines use. i am not a pro rider or anything but i work my bikes hard even the 500 hence i have a destroyed engine, i would like anyone and everyone to have there say on this so i can make the best choice. thanks in advance
john
Logged

Offline martinfan30

  • Sr. Member
  • ****
  • Posts: 456
  • 2000 KX500
Re: BEST K5 CON ROD
« Reply #1 on: October 30, 2010, 08:57:35 AM »
I really am a fan of OEM internals...
Logged
2000 KX500
2005 XR650L

Neither are stock, and both are great desert bikes.

Offline jonny500

  • Hero Member
  • *****
  • Posts: 580
Re: BEST K5 CON ROD
« Reply #2 on: October 30, 2010, 09:14:10 AM »
oem are the same as prox, all conrods are forged?
Logged

Offline kwakman

  • Hero Member
  • *****
  • Posts: 879
  • Kwikasfuki KX500
Re: BEST K5 CON ROD
« Reply #3 on: October 30, 2010, 10:18:39 AM »
i dont think they are all forged.vesrah are, I think hotrods are, but have been known to fail, wiseco are forged, and I think the kwak rod is too.dont think prox are but not certain.
Logged
And lo, I did loft the front wheel and carried it forth to the unbelievers, and cast it down before them and said unto them ''look now upon the might of my throttle control ye pitiful cretinous ones''
And the unbelievers did quake in their boots....

Offline don46

  • Hero Member
  • *****
  • Posts: 1,140
Re: BEST K5 CON ROD
« Reply #4 on: October 30, 2010, 12:31:48 PM »
high HP over time will break KX rods, I'm spraying nitrous and using a Titanium Rod. Not sure where to get another one, the one I have  I got off ebay.
Logged
Live today, for tomorrow may never come

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: BEST K5 CON ROD
« Reply #5 on: October 30, 2010, 04:40:32 PM »
Quote from: don46 on October 30, 2010, 12:31:48 PM
high HP over time will break KX rods, I'm spraying nitrous and using a Titanium Rod. Not sure where to get another one, the one I have  I got off ebay.

I'd like to get my hands on a Titanium rod that was junk and reverse engineer it and make a set of prints so I could see about having some made.
If you have one laying around I would be happy to make the plans, send you a copy as well as send the rod back.
Just a thought....
« Last Edit: October 30, 2010, 04:43:55 PM by sandblaster »
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline gortex

  • Jr. Member
  • **
  • Posts: 34
Re: BEST K5 CON ROD
« Reply #6 on: October 30, 2010, 05:47:04 PM »
Getting my motor rebuild with a Cr500 rod to hold up to the increased hp we going for. Meant to be one of the strongest rod around.
Logged

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: BEST K5 CON ROD
« Reply #7 on: October 31, 2010, 05:02:56 AM »
Quote from: gortex on October 30, 2010, 05:47:04 PM
Getting my motor rebuild with a Cr500 rod to hold up to the increased hp we going for. Meant to be one of the strongest rod around.
what year rod are you going to use, I believe honda has two different lengths, between the years on the 5's.  Also, what brand?
Logged
America is all about speed. Hot, nasty, bad-ass speed.

Offline kwakman

  • Hero Member
  • *****
  • Posts: 879
  • Kwikasfuki KX500
Re: BEST K5 CON ROD
« Reply #8 on: October 31, 2010, 09:28:47 AM »
I dont think the cr rod is any stronger than the kx rod, if you were making them they would just be the same quality for each app surely? Does any one know the length/s of the cr rod, centre of small end to centre of big end? I believe kx rod is 14.5cm...
Logged
And lo, I did loft the front wheel and carried it forth to the unbelievers, and cast it down before them and said unto them ''look now upon the might of my throttle control ye pitiful cretinous ones''
And the unbelievers did quake in their boots....

Offline don46

  • Hero Member
  • *****
  • Posts: 1,140
Re: BEST K5 CON ROD
« Reply #9 on: October 31, 2010, 11:48:02 AM »
Quote from: RoostDaddy on October 31, 2010, 05:02:56 AM
Quote from: gortex on October 30, 2010, 05:47:04 PM
Getting my motor rebuild with a Cr500 rod to hold up to the increased hp we going for. Meant to be one of the strongest rod around.
what year rod are you going to use, I believe honda has two different lengths, between the years on the 5's.  Also, what brand?

You are absolutely correct, although one is like a pre 87ish and the other is like 87 on. The pre 87 are almost unobtainable, or so I was told, and it was shorter that the current rod, I have both and could measure them. I think the reason that Honda has less rod issues is due to the shorter stroke. I have a motor built with the Honda rod and piston, a true 560, and for a trail bike it would probably be great the thing will pull a truck but doesn't rev quick, I also used a 87 cylinder, the thinking was that the huge bore wouldn't be affected by the center KIPs. There are some guys now having 90-91mm KX pistons so I may put the KX rod back in and get one and try it.
Logged
Live today, for tomorrow may never come

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: BEST K5 CON ROD
« Reply #10 on: November 01, 2010, 09:17:11 AM »
Don, from what I have seen the '85-'86  has a "short" rod length of 178.45mm and the '87-'01 has a "long" rod length of 183.6mm
 I have also seen KX pistons ranging from 89-91mm using the Wossner piston.
Logged
America is all about speed. Hot, nasty, bad-ass speed.

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: BEST K5 CON ROD
« Reply #11 on: November 01, 2010, 11:50:27 AM »
jason   those must be outside to outside measurement.
Logged

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: BEST K5 CON ROD
« Reply #12 on: November 02, 2010, 09:28:08 AM »
Quote from: kaw rider on November 01, 2010, 11:50:27 AM
jason   those must be outside to outside measurement.
yeah, I'm pretty sure that was overall length.  It's not my measurements, just what I've found, so they may not be 100% accurate.  If someone knows for sure, Post-Up.
Logged
America is all about speed. Hot, nasty, bad-ass speed.
Pages: [1]   Go Up
« previous next »