Author Topic: Timing way out  (Read 3780 times)

0 Members and 1 Guest are viewing this topic.

Offline skippyhenry

  • Newbie
  • *
  • Posts: 7
Timing way out
« on: May 06, 2010, 01:08:55 AM »
need help with my timing,its been a bugger to start since i had the motor rebuilt. Ive had the electrics replaced, new magneto, stator rewound, its getting spark,back fires a lot and then starts but wont idle. Reeds are good, carburator is new, so what I did is ran a timing light to check timing it should be at about 7 deg but is firing at 90 deg, half way up the bloody barrell is that premature or what  :? oh its a k500 1989 what can i do to get it back to 7 deg thanks

Offline bob larry

  • Full Member
  • ***
  • Posts: 150
Re: Timing way out
« Reply #1 on: May 06, 2010, 03:45:32 AM »
Get the manual out and go through the timing proceedure.... :mrgreen:
2001 KX500

Offline maddoggy

  • Hero Member
  • *****
  • Posts: 711
  • K5 @ ST. ANTHONY DUNES
Re: Timing way out
« Reply #2 on: May 06, 2010, 03:53:57 AM »
are you sure that the key was installed when the flywheel was put on the shaft? with timing that far off, i cant think of anything else it could be. pull the flywheel and verify that the key is in place and that it is not sheared from an initial backfire.

Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: Timing way out
« Reply #3 on: May 06, 2010, 05:38:13 AM »
 I'm sorry I don't know how to put everything in order  :|
  You should find what you need here:
http://www.kxriders.com/coppermine/thumbnails.php?album=259&page=2
   Tuck\o/
"The Truth Has No Agenda"

Offline allan1353

  • Jr. Member
  • **
  • Posts: 29
Re: Timing way out
« Reply #4 on: May 06, 2010, 10:39:50 AM »
To me it sounds like a sheared key as maddoggy pointed out.

Offline skippyhenry

  • Newbie
  • *
  • Posts: 7
Re: Timing way out
« Reply #5 on: May 06, 2010, 11:11:27 PM »
thanks for the replys, the key is good but the magneto is the wrong one for that year motor.So am going to get a new key way cut into the magneto. Fingers x :-D

Offline Polar-Bus

  • Hero Member
  • *****
  • Posts: 1,023
Re: Timing way out
« Reply #6 on: May 07, 2010, 12:40:30 AM »
thanks for the replys, the key is good but the magneto is the wrong one for that year motor.So am going to get a new key way cut into the magneto. Fingers x :-D

This sounds like a recipie for detonation disaster too me....
01' KX500
'84 GPz1100
'87 GSX-R  750
'06 HD Fatboy
'73 Kawi H1
'03 CRG KX500 Shifter kart

Offline maddoggy

  • Hero Member
  • *****
  • Posts: 711
  • K5 @ ST. ANTHONY DUNES
Re: Timing way out
« Reply #7 on: May 07, 2010, 03:30:38 AM »
i agree with polarbus. i would not take a chance on cutting a new keyway. sounds like a disaster waiting to happen. if you cant afford a new one now, you would be better off to save up for a while and buy the proper mag. seriosly, i wouldn't try the repair. think about what pre-det. does. it fires the fuel/air charge while the piston is still on the way up tries to force it back down. bad, bad, bad things can happen to your motor. motor repairs could cost more than the proper part. not being a jerk here, just trying to help.
                                                                              maddoggy

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: Timing way out
« Reply #8 on: May 07, 2010, 05:40:43 AM »
you would be money ahead to upgrade to a 90 and newer ignition

Motorrad

  • Guest
Re: Timing way out
« Reply #9 on: May 07, 2010, 06:37:43 AM »
Have you checked it with a degree wheel, and dial indicator down the plug hole?   I wouldn't trust a timing light in this application....

Offline skippyhenry

  • Newbie
  • *
  • Posts: 7
Re: Timing way out
« Reply #10 on: May 07, 2010, 12:10:04 PM »
All right guys you've scared the pants off me, I will get the right magneto. Thanks for the replies. And have a good weekend.