Author Topic: 1984 KX 500 Jetting recomendations  (Read 6883 times)

0 Members and 1 Guest are viewing this topic.

Offline electech

  • Jr. Member
  • **
  • Posts: 11
1984 KX 500 Jetting recomendations
« on: December 20, 2009, 11:59:09 AM »
My buddy and I are trying to tune a 84' 500, we keep fouling plugs and it seems really rich on bottom.  It has a fresh top and bottom end and new reeds. The carb is set to spec and runs great as long as you keep it cleaned out. Anyone with experience on this old of a machine please help. We are at 200ft here in East Texas. :cry:

Offline sintax

  • Full Member
  • ***
  • Posts: 113
Re: 1984 KX 500 Jetting recomendations
« Reply #1 on: December 20, 2009, 12:16:51 PM »
what are your current specs?

give this chart a shot, it will get you close.

http://www.kxriders.com/forums/index.php?page=11

Offline electech

  • Jr. Member
  • **
  • Posts: 11
Re: 1984 KX 500 Jetting recomendations
« Reply #2 on: December 20, 2009, 01:05:30 PM »
The chart does not speacify what carb they are for.  If the chart is for the Keihen PWK it wont help me a bit. My carb is the mikuni vm38ss.  Pilot-40, Clip-2, Main-172, Screw-1.5 turns. 200ft, 65 degrees.

Offline YUNGGUNNAZ

  • Full Member
  • ***
  • Posts: 219
Re: 1984 KX 500 Jetting recomendations
« Reply #3 on: December 20, 2009, 02:09:06 PM »
was this motor pressured tested for leaks?how much break in time on it and how was it done?are reeds in good shape and closed?doesn't this one have copper head gasket?how was that sealed?what pipe?answer these first and you'll probably get better responses.jmo.

Offline electech

  • Jr. Member
  • **
  • Posts: 11
Re: 1984 KX 500 Jetting recomendations
« Reply #4 on: December 20, 2009, 02:35:53 PM »
Motor was pressure tested, 5 hours break in and broke in similar to forum recomendations, reeds are brand new, cant remember what head gasket was used, pipe is stock and sealed.  Bike ran the same before rebuild. With fresh plugs will start first kick cold with choke and clean up and run.  After it gets warm low speed trail and or short idiling will cause it to load up severly and will usually clean out and run. Other times will bog, back fire and die and its over. Plugs  BR9 NGK, if there is anything I left out that might help let me know.

Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: 1984 KX 500 Jetting recomendations
« Reply #5 on: December 20, 2009, 04:16:35 PM »
  electech,

  This may sound like old hat stuff however keep notes and only change one thing at a time.
And.. this is just another opinion from the internet...just some stuff to consider..   

The easiest thing to try right off is raise the clip on the needle.  and smaller pilot.
 If your midrange cleans up a bit you are headed in the right direction.

You mentioned you all ran a pressure test on the case so your not drawing trans fluid...
    If you are not running the old girl flat out, drop a heat range. go for a short ride and check the plug.  Only reason I'm saying this is I run a heat range 7.  I don't have alot of WOT territory  out hear and run a hotter plug account to keep it clean.
  I know it's an air cooled bike, most guys run ngk 8's and dune riding or maybe racing run a 9.
     Are you running hard enough to keep enough heat in the plug to burn off the oil
  at 65 deg F
 
Fuel /oil ratio : Lot's of Playriders run 40:1 with no problem, I'm not saying jump into it,
however you might sneak up on it if the bike is mostly stock and not ridden all that hard.
 
 Carb: are the needle and slide in good shape and are the jets relatively new.
           If those are original parts they could be out of spec. 
The easiest thing to try right off is raise the clip on the needle.  and smaller pilot.

 Air Filter oiled too heavily .   
    There could be several things going on at once, Have patience Grass Hoppa!
   Tuck\o/
"The Truth Has No Agenda"

Offline electech

  • Jr. Member
  • **
  • Posts: 11
Re: 1984 KX 500 Jetting recomendations
« Reply #6 on: December 20, 2009, 10:47:14 PM »
 Thanks Tuck, we are getting some hotter plugs and switching to iridium asap, the carb is original but you should see the bike it is like new condition and you can tell it was hardly ridden.   We only did the top and bottom end cause we were in the machine just looking things over.  We picked the bike up from a guy who bought it new in the early 80s and never rode it much then put it in storage until we bought it. The changes we have made have been one at a time, this has been an on-going problem since the spring.  We just went through two CR 500s and are now trying to work the bugs out of this ol girl while its cool.  Our weather goes from 70 to 30 and everything in between this time of year.  The bike wont be ridden too hard, we are planning on taking it to Colorado in the summer and doing some trail riding, otherwise we just fire it up on the weekends and run it some.  Im not that familiar with plug problems, none of my bikes have ever had fouling problems and I like to think i can tune a carb pretty good but this thing is something else.  Anyway thanks for the info. Also we are running 32:1 ratio and the air filter is good.

Offline Hillclimb#42

  • Hero Member
  • *****
  • Posts: 991
  • '97 kx 500, '96 kx 250, '99 KTM 380
Re: 1984 KX 500 Jetting recomendations
« Reply #7 on: December 21, 2009, 10:59:12 AM »
double check the floats, that has fixed my 250 with a cold foul issue. Does it still foul them after the bike is warmed up? Mine would foul one mostly on the first start-up of the day, until adjusting them a little tighter.
   :-D '84 Beast. Sounds like a good find. Riding them at all wears out parts, so don't be afraid to check it all out, well maintained is way better than sitting still, for all the seals, gaskets, and bearrings. It getting hard to find parts for older ones too, good luck with her.

Offline electech

  • Jr. Member
  • **
  • Posts: 11
Re: 1984 KX 500 Jetting recomendations
« Reply #8 on: December 29, 2009, 12:57:59 PM »
We ended up going leaner on the pilot again and swapped to one step hotter
in an iridium an we have not fouled another plug yet. Thanks for the help and suggestions.

Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: 1984 KX 500 Jetting recomendations
« Reply #9 on: December 29, 2009, 03:07:33 PM »
 Thanks for reporting back!
Someone else may come up against this in the future and have some direction.
   It's not every day someone ask's about an '84 with a mikuni!!
    Best of luck, and drop a photo or two as I don't think I've seen an '84 KX other than an ad in a magazine.   And like I said, You might be helping someone out in the future  :-D
   Tuck\o/
"The Truth Has No Agenda"

Offline electech

  • Jr. Member
  • **
  • Posts: 11
Re: 1984 KX 500 Jetting recomendations
« Reply #10 on: December 30, 2009, 02:49:29 AM »
Here are some pics.





Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: 1984 KX 500 Jetting recomendations
« Reply #11 on: December 30, 2009, 03:45:41 AM »
 Thanks Elec,
  You weren't Kidding!   That old girl is in great shape for her age!   
 I'm betting that's the first picture of an '84 here, and if not the first, surely a most  unmolested one! 
   Very Cool, OLD SCHOOL   :mrgreen:
     Tuck\o/
"The Truth Has No Agenda"