Author Topic: "B" designation on kawasaki pistons  (Read 4254 times)

0 Members and 1 Guest are viewing this topic.

rdg2

  • Guest
"B" designation on kawasaki pistons
« on: December 04, 2003, 05:46:11 AM »
What is with the "B" designationon kawasaki pistons when looking at the microfiche:

PISTON-ENGINE,(B)

What does this stand for?

Also:  Are "Pro-X" pistons pretty good?  Which is better Kawasaki Genuine or Pro X?  Who is a good online vendor to buy a piston kit from?

Thanks
Rob

Offline demographic

  • Hero Member
  • *****
  • Posts: 825
"B" designation on kawasaki pistons
« Reply #1 on: December 04, 2003, 07:25:42 AM »
Pro X are OE pistons, made in the same factory and everything :)

The answers to the letter designation on your piston can be found if you CLICK HERE

Regards Scott

Offline John

  • Sr. Member
  • ****
  • Posts: 321
    • http://www.hallbergs.net
"B" designation on kawasaki pistons
« Reply #2 on: December 04, 2003, 10:42:00 AM »
Scott,

If you are changing pistons, consider the Wiseco pistons. I have only good experience of them so far. They actually improved the overall performance of my bikes and they are cheaper than the originals.

//John

Offline demographic

  • Hero Member
  • *****
  • Posts: 825
"B" designation on kawasaki pistons
« Reply #3 on: December 05, 2003, 07:42:33 AM »
Quote from: John
Scott,

If you are changing pistons, consider the Wiseco pistons. I have only good experience of them so far. They actually improved the overall performance of my bikes and they are cheaper than the originals.

//John


Errrr, If you look at the top of the page you will see that is rdg2 otherwise known as Rob who was asking about pistons and I was just replying to his question :)

I have an awfully nice Wiseco fitted in my KX and they are also lighter than stock :D

Offline John

  • Sr. Member
  • ****
  • Posts: 321
    • http://www.hallbergs.net
"B" designation on kawasaki pistons
« Reply #4 on: December 05, 2003, 09:04:27 AM »
Sorry,

I was confused there, should have said Rob not Scott. My mistake! But then again, I am confused most of the time...

//John

Rick

  • Guest
"B" designation on kawasaki pistons
« Reply #5 on: December 08, 2003, 06:31:43 AM »
I have used both ProX and Wiseco with good success.  Ironically, the only piston I have ever broken was a stock unit.  Fortunately, low RPM failure, so no damage.

Opt for either unit depending upon availability and price.

Good Luck

Rick

Biggreenmonster

  • Guest
"B" designation on kawasaki pistons
« Reply #6 on: December 09, 2003, 11:55:21 AM »
I think the "B" is for a larger piston to take up some of the side clearance on a worn cylinder..its just to tighten things up...Am i right guy's?
I use Wiseco pistons/best pistons in the world...they are a work of art!!

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
"B" designation on kawasaki pistons
« Reply #7 on: December 14, 2003, 04:06:04 AM »
My opinion is use the Wiseco!
Better, much lighter and give a better throttleresponse :D
You get cracks in the orginalpiston below the wristpin inside the piston.
When you buy a new piston campfer the piston-ends at the skirt,you got better oilfilm inside the cylinder if you do that.
How many of you desertriders drill a boosthole in the piston?
Iceroad champion 2006,still 2007,even 2008 without a single race!

Biggreenmonster

  • Guest
"B" designation on kawasaki pistons
« Reply #8 on: December 17, 2003, 12:48:23 PM »
never drilled port hole for KX500....but i had several CR500's that i drilled relief holes in the piston in line with the exhaust port bridge to carry extra lubricant.
I am curious about the boosthole though!