Author Topic: tank leak repair  (Read 5535 times)

0 Members and 2 Guests are viewing this topic.

Offline KX500freak

  • Hero Member
  • *****
  • Posts: 1,028
  • KX500 - Have a Wheelie good weekend
tank leak repair
« on: March 02, 2009, 01:13:06 AM »
got to get my tank fixed,
sec hand still way expensive ,so im trying to find ways to repair it
any suggestions on what to buy ,how to,s
its a 98 kx250 fuel tank
maybe someone can tell me what plast it,s made off ..
i have the section damaged where it prolly was stamped in.
can,t find anything other stamp on the thing  :|

thanks in advance


freak
Dutch Team Green 91-94-01 KX500

Offline Dutch-K5 Fan

  • Hero Member
  • *****
  • Posts: 759
Re: tank leak repair
« Reply #1 on: March 02, 2009, 04:57:57 AM »
Hey Menno al ok???

Is it a big hole or just a smale crack??
If its not to big you can meld it with a soldering iron an fil it with a zipty.

Dutchie
Proud owner of a KX500AF

Offline cbxracer30

  • Sr. Member
  • ****
  • Posts: 304
Re: tank leak repair
« Reply #2 on: March 02, 2009, 07:25:48 AM »
Advanced auto sells a plastic gas tank repair epoxy. It works very well I've used it on a couple tanks . It is very runny though so be careful.
Yep, you can ride it - if YOU can start it !!

Offline Dutch-K5 Fan

  • Hero Member
  • *****
  • Posts: 759
Re: tank leak repair
« Reply #3 on: March 02, 2009, 07:47:10 AM »
Advanced auto sells a plastic gas tank repair epoxy. It works very well I've used it on a couple tanks . It is very runny though so be careful.

Is it a coating for inside the tank??

Maybe this could work than Menno!
http://www.frost-auto.nl/?p=productsMore&iProduct=49


Dutchie
Proud owner of a KX500AF

Offline cbxracer30

  • Sr. Member
  • ****
  • Posts: 304
Re: tank leak repair
« Reply #4 on: March 02, 2009, 09:45:33 AM »
No it's a 2 part black epoxy that goes on the outside. Like I said it is very runny at first but sets up very fast. To prep the tank all you have to do is clean the area with sand paper.
Yep, you can ride it - if YOU can start it !!

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: tank leak repair
« Reply #5 on: March 02, 2009, 11:02:07 AM »
I've never seen any type of glue or epoxy that stuck to a plastic gas tank for very long. Not even the stuff that they claim is for it. The best luck I have had for repairing tanks is with plastic welding. I like to use an old fender, you can cut it into strips to be used as filler rod. Then you have the right color and the right plastic to make the repair. The down fall is that plastic welding is an art just like any other type of welding. When I do a tank repair with heat I like to fill it half way with water so if I want to cool the repair I can just role the tank over.
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: tank leak repair
« Reply #6 on: March 02, 2009, 11:35:40 AM »
I too have used the plastic gas tank epoxy from an auto parts store with great results.  Mine was the clear, not the black.
America is all about speed. Hot, nasty, bad-ass speed.

Offline KX500freak

  • Hero Member
  • *****
  • Posts: 1,028
  • KX500 - Have a Wheelie good weekend
Re: tank leak repair
« Reply #7 on: March 02, 2009, 12:10:26 PM »
Hey Menno al ok???

Is it a big hole or just a smale crack??
If its not to big you can meld it with a soldering iron an fil it with a zipty.

Dutchie

it s not good ,no job ,no money ,thanks fer asking pete  :wink:

it,s a huge crack ,all off the bottom hangs loose..

Advanced auto sells a plastic gas tank repair epoxy. It works very well I've used it on a couple tanks . It is very runny though so be careful.


thanks for your input ,but i determined it will not be repairable :cry:



I've never seen any type of glue or epoxy that stuck to a plastic gas tank for very long. Not even the stuff that they claim is for it. The best luck I have had for repairing tanks is with plastic welding. I like to use an old fender, you can cut it into strips to be used as filler rod. Then you have the right color and the right plastic to make the repair. The down fall is that plastic welding is an art just like any other type of welding. When I do a tank repair with heat I like to fill it half way with water so if I want to cool the repair I can just role the tank over.


thanks BDI

i tried to plastic weld ,found out the whole bottom was cracked,while prepairing..
so i,m stuck with buying the sec-hand tank ,
just because i,m very afraid the tank will crack wide open.
with me sitting on it while doin a 70 mph straight ,
i don, t wanna think of it,a gallon of racegas sprayed over the very hot pipe & me legs

 
Dutch Team Green 91-94-01 KX500

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: tank leak repair
« Reply #8 on: March 02, 2009, 12:30:52 PM »
If the tank has cracked like that it's probably brittle from age. Sounds like it has hit the end of it's life cycle to me.
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline Johnniespeed

  • Hero Member
  • *****
  • Posts: 575
  • The Thrill of Speed overcomes the fear of Death.
Re: tank leak repair
« Reply #9 on: March 02, 2009, 01:30:00 PM »
I had a melted hole in a CR250 tank, from the exhaust being too close.  I simply drilled a round hole at the leak , welded a flat washer to a carriage bolt, put a rubber washer on the bolt and fed it into the tank with a extendable magnet. Then on the outside I placed a rubber washer, then a flat washer, then a nut, I used a cutoff wheel to trim off the protruding threads. I did apply locktite first. This repair never, ever, leaked and as far as I know, the bike is still being used this way. Maybe next time, I would try a chrome washer and chrome acorn nut on the outside.
 John
Spring is here and the Mighty 500 wants to ride.
 2004 KX500 E16
 Michigan has the best groomed and mapped trail system, check out the Cycle Conservation Club of Michigan trail maps.

Offline KXcam22

  • Hero Member
  • *****
  • Posts: 1,677
Re: tank leak repair
« Reply #10 on: March 02, 2009, 04:53:42 PM »
Does Clarke make a tank for the K5? I was looking at their tanks and noticed they make a range for quite a few years of bikes.  Also try justgastanks.com.  Cam.

Offline turtle22

  • Full Member
  • ***
  • Posts: 180
  • '89 & '01 kx500 '87 fxr HD '80 xr500
Re: tank leak repair
« Reply #11 on: March 02, 2009, 04:58:21 PM »
yes clarke's does. a 4 gallion for under$200(&two other styles,also). its on the websit u mentioned
lets ride

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: tank leak repair
« Reply #12 on: March 02, 2009, 05:09:47 PM »
I do think they offer a stock replacement tank for the kx500. There has been a lot of kx500 tanks go tits up over the years so I think they started producing them.
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline KX500freak

  • Hero Member
  • *****
  • Posts: 1,028
  • KX500 - Have a Wheelie good weekend
Re: tank leak repair
« Reply #13 on: March 03, 2009, 03:28:22 AM »
If the tank has cracked like that it's probably brittle from age. Sounds like it has hit the end of it's life cycle to me.


it,s not brittle yet ,but it is wear on the edges of it ,s bottom ,
making it thin and then easy to crack.as it did..

I had a melted hole in a CR250 tank, from the exhaust being too close.  I simply drilled a round hole at the leak , welded a flat washer to a carriage bolt, put a rubber washer on the bolt and fed it into the tank with a extendable magnet. Then on the outside I placed a rubber washer, then a flat washer, then a nut, I used a cutoff wheel to trim off the protruding threads. I did apply locktite first. This repair never, ever, leaked and as far as I know, the bike is still being used this way. Maybe next time, I would try a chrome washer and chrome acorn nut on the outside.
 John


haha i can imagine it right away ,cool solution.
but i,m in the process of fixing a tore off tankbottom,
to bad your way will not go on this one :(

thnx !


Does Clarke make a tank for the K5? I was looking at their tanks and noticed they make a range for quite a few years of bikes.  Also try justgastanks.com.  Cam.



thanks cam ,but hate to say ..embarrased i was..went to the premium kawi dealership ...
the told me it even isn,t  a kx tank ,
they said kawi makes no grey tanks at all ,so i stuck with it  :roll:


guys thanks alot !!


i ,m gonna get a proper fixing kit fer it and will let you know
Dutch Team Green 91-94-01 KX500

Offline Dutch-K5 Fan

  • Hero Member
  • *****
  • Posts: 759
Re: tank leak repair
« Reply #14 on: March 03, 2009, 04:31:29 AM »
Maybe it was already an aftermarket tank menno.
Is it realy grey or light black??? Kawa makes black tank fur sure.
And for the clarktank I've E-mailed them but have no anwser yet.
Wanted to know if there is a euro or even benelux dealer for them, for a bigger than on my AF.
In Holland there more into aluminium tanks, but they cost to much!!!!?700,- and up.


Ps sh#&$# to here your still without work(and money) man.

Dutchie
Proud owner of a KX500AF