« previous next »
Pages: [1]   Go Down

Author Topic: ring gap spec  (Read 4389 times)

0 Members and 1 Guest are viewing this topic.

KXT500

  • Guest
ring gap spec
« on: April 03, 2003, 04:55:26 AM »
what are the specs for the ring gap? my gause is in .001" (not metric)
thankjs
chris
Logged

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
ring gap spec
« Reply #1 on: April 03, 2003, 05:06:55 AM »
There isn't one. You put them in and go, just make sure they are aligned with the little pins in the ring grooves or it's going to be a bad day ;)
Logged

KXT500

  • Guest
ring gap spec
« Reply #2 on: April 03, 2003, 06:04:28 AM »
so how do you know when to replace them? there has to be some spec. how would you know if the factory screwed one up? you would eat your cylinder. i would never build and engine and not check the end gap :shock:
Logged

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
ring gap spec
« Reply #3 on: April 03, 2003, 06:53:00 AM »
These aren't automotive engines, I asked the same question the first time I did a topend. I asked that question AGAIN when I went to MMI for the K-Tech program. There isn't an end gap setting. Your BEST indicator for replacement of rings in the topend is to use a compression testor and verify that the compression is within service limits (165psi - 110psi). I doubt the soft material the rings are made from will eat a Nikasil cylinder. At least I have never seen it happen.

Quote from: KXT500
so how do you know when to replace them? there has to be some spec. how would you know if the factory screwed one up? you would eat your cylinder. i would never build and engine and not check the end gap :shock:
Logged

ShanMan

  • Guest
ring gap spec
« Reply #4 on: April 03, 2003, 07:20:46 AM »
Asa mechanical engineer, I can assure you that the gap is not .001". I might buy .010" as a best case. The ring is most certainly softer than the cylinder by design. Of course, if the engine is allowed to run to lean too long, you will anneal the ring material and process of meltdown occurs.  :)
Logged

Rick

  • Guest
ring gap spec
« Reply #5 on: April 03, 2003, 11:03:18 AM »
You guys use rings in your motors??  :shock: How does it work?  How's the power?

My pistons fit sooo tight that I don't need rings.  When I get a little piston slop, I just use a little JB Weld on the piston, and sand to the proper fit......

Rick
Logged

sdkx500

  • Guest
ring gap spec
« Reply #6 on: April 03, 2003, 11:28:12 AM »
laughing......................
Logged

DrMojo

  • Guest
Here is the ring information for your KX-500
« Reply #7 on: April 04, 2003, 12:52:47 AM »
Chris,

Here is what you are looking for.  This applies to the KX500 motor built after 1988:

Piston ring end gap 0.2mm to 0.4mm (service limit is 0.7mm)

Piston groove width 1.24mm to 1.26mm (service limit is 1.34mm)

Piston ring thickness 1.17mm to 1.19mm (service limit is 1.10mm)

Piston ring-to-groove clearance 0.05mm to 0.09mm (service limit is 0.19mm)

I hope this helps,
Al
Logged
Pages: [1]   Go Up
« previous next »