Author Topic: I can't believe it!!!!  (Read 3453 times)

0 Members and 1 Guest are viewing this topic.

Offline machine

  • Sr. Member
  • ****
  • Posts: 250
I can't believe it!!!!
« on: March 30, 2005, 10:08:00 AM »
Man, I can?t believe I did it!!!!!!
I?ve owned a lot of bike, and now when I have a big trip planed in 2 weeks is the first time I strip out a drain plug!!!!
GGGGGGEEEEEEEEEEEEZZZZZZZZZZZZZZZZ!!!!!!!!!!!!!!!!!!!!!

Ok, what?s next?
Helicoil, or just drill it out, and re-tap to the next size?
What would the next size be?
Any tricks or tips???

Ooooooooooohhh, this sucks!!!!  :cry:

Offline Arigato

  • Hero Member
  • *****
  • Posts: 516
I can't believe it!!!!
« Reply #1 on: March 30, 2005, 10:20:26 AM »
Drill it out and use a time sert for the original size plug.  That does suck.

Offline machine

  • Sr. Member
  • ****
  • Posts: 250
I can't believe it!!!!
« Reply #2 on: March 30, 2005, 12:11:53 PM »
I'm not sure what time sert is?
Where can I get one?

Offline Arigato

  • Hero Member
  • *****
  • Posts: 516
I can't believe it!!!!
« Reply #3 on: March 30, 2005, 12:26:43 PM »
You should be able to find one at an auto parts store.  It's like a helicoil but it's more premanent and solid.

Offline KXcam22

  • Hero Member
  • *****
  • Posts: 1,677
I can't believe it!!!!
« Reply #4 on: March 30, 2005, 12:40:13 PM »
Machine,
  Don't sweat it. I stripped mine right before a ride and wasn't even late.  The repair was easy. Here is what I did:

Lay the bike on it's side and tap out the hole to the next size for a helicoil.  It helps to coat the tap with grease to catch most of the aluminum chips.  Install the helicoil with red loctite.  Pour a liter of some cheap motor oil through to flush out any pesky aluminum chip that may still be in there.  Install the drain plug and lockwire it.  The lockwire is a good thing as you tend not to do the "hercules" thing when tightening it up (since it can't come out).  I've done sparkplug holes this way with good results too.  Good luck. Hope this helps. Cam.

Offline machine

  • Sr. Member
  • ****
  • Posts: 250
I can't believe it!!!!
« Reply #5 on: March 30, 2005, 02:17:35 PM »
Ok, thanks for the info guys!
I?m going to take both of your advice.
I like the sound of the ?Time-Sert? and I will use Cam?s directions.

Thanks aging guys.
I?ll let ya know how it goes.
Now I just need to find a place to get ?Time-Sert? kit QUICK!!!!

Here?s some info on them.
http://www.timesert.com/



Kev?

Offline gowen

  • Resident Newbie
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1,350
  • www.KXRiders.com
I can't believe it!!!!
« Reply #6 on: March 31, 2005, 04:48:13 AM »
Most motorcycle service shops have them on hand. I had my local Honda shop do it while I was on the way to ride. It took them less than 30 minutes.

Offline KXcam22

  • Hero Member
  • *****
  • Posts: 1,677
I can't believe it!!!!
« Reply #7 on: March 31, 2005, 09:11:44 AM »
Arigato,
  Those timeserts look nice. One step better from a helicoil. Cam.

BrianSM

  • Guest
I can't believe it!!!!
« Reply #8 on: March 31, 2005, 11:21:44 AM »
The guy before me hosed up the threads so he tapped in a 7/16" machine thread which finally screwed up...... :roll:  Time serts as described are great !!! but try to find one ..... aircraft industry is where they come from....... as per the other post laying the bike down etc and using the heli coil.... thats exactly what I did.....I did that so I could re use the original style plug.......I put one wrap of teflon tape around the threads
and change my oil after every race style works perfect... no leaks...

Offline machine

  • Sr. Member
  • ****
  • Posts: 250
I can't believe it!!!!
« Reply #9 on: March 31, 2005, 03:27:30 PM »
Thanks 2 All of ya!
I took it 2 the dealer! $70 bucks for a "Time-sert" installed!



"but try to find one ..... aircraft industry is where they come from."


That's my industry, and I looked @ McMaster Carr, Rutland, and MSS.
And no one had the time-sert.  ????