« previous next »
Pages: [1]   Go Down

Author Topic: Exhaust port not centered!!!  (Read 4731 times)

0 Members and 4 Guests are viewing this topic.

Offline MOTOSCOTT

  • Jr. Member
  • **
  • Posts: 10
Exhaust port not centered!!!
« on: February 13, 2012, 03:19:17 PM »
2008 kx250f/92-500
Got in contact with Jfab and rails on the way!
 Cut my frame rails and prepped.
 Drilled my pivot with 43/64 and the fit is perfect.
 Fine tuned the outer swingarm spacers :? to get a nug fit for the rear engine/swing arm/frame. Installed my motor to get a feel for the final cut for the correct height for the exhaust pipe and !!!!!!!!!!

My exhaust port is about an 1/8 of an inch off center to the left of the front frame down tube. Is this normal? I dont think I have enough to trim in the swing arm spacers to compensate. Chain alignment looks O.K.

Any suggestions.
NO PICS YET COMMING SOON (CAMERA DOWN)

Logged

Motorrad

  • Guest
Re: Exhaust port not centered!!!
« Reply #1 on: February 13, 2012, 03:54:21 PM »
Hmm thinking what it could be..     

Waiting on pics
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Exhaust port not centered!!!
« Reply #2 on: February 13, 2012, 04:18:58 PM »
I took a look at my unfinished project and my outlet is split evenly.
So I looked at the possibilities.
Bent frame
Bent pivot pin
Misaligned holes in the engine cases.
Oblong holes in the frame.
What else could it be?
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline kwakman

  • Hero Member
  • *****
  • Posts: 879
  • Kwikasfuki KX500
Re: Exhaust port not centered!!!
« Reply #3 on: February 14, 2012, 02:34:25 AM »
does it line up if you slacken all the bolts up? if not, twisted frame would be a possibility.K.
Logged
And lo, I did loft the front wheel and carried it forth to the unbelievers, and cast it down before them and said unto them ''look now upon the might of my throttle control ye pitiful cretinous ones''
And the unbelievers did quake in their boots....

Offline jonny500

  • Hero Member
  • *****
  • Posts: 580
Re: Exhaust port not centered!!!
« Reply #4 on: February 14, 2012, 07:07:32 AM »
did you take the same amount off both swing arm bushes
« Last Edit: February 14, 2012, 06:46:06 PM by jonny500 »
Logged

Motorrad

  • Guest
Re: Exhaust port not centered!!!
« Reply #5 on: February 14, 2012, 08:01:57 AM »
The reason they make frame jigs?

Frame go "boing" when you made last cut?
Logged

Offline 81cr450

  • Hero Member
  • *****
  • Posts: 887
Re: Exhaust port not centered!!!
« Reply #6 on: February 14, 2012, 12:51:35 PM »
I've done a couple on hondas, so keep that in mind but... Your worrying to much, it doesnt have to center in the crotch of the Y. Undo the 2 lower bolts with just the swinger bolt in place loose, Then take the case & just raise it up & down & make sure it fits smoothly in between the other to mounting points. As long as it will pivot into the other 2 mounts smoothly your ok. I'll bet the factory steel frame bike doesnt center the pipe perfect. Sprocket alignment is the key
Logged
if I only had a pair, I could actually ride this thing

& to the people I like  FYYFF

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Exhaust port not centered!!!
« Reply #7 on: February 14, 2012, 04:48:42 PM »
Quote from: Motorrad on February 14, 2012, 08:01:57 AM
The reason they make frame jigs?

Frame go "boing" when you made last cut?

Your killing me  :lol:
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline MOTOSCOTT

  • Jr. Member
  • **
  • Posts: 10
Re: Exhaust port not centered!!!
« Reply #8 on: February 21, 2012, 01:53:10 AM »
Verified frame is straight. Found the culprit, bad drill on the swing arm thru cases! All squared up and O.K. Amazing how small difference in the angle made a huge difference in the front!

Waiting on rails from JFAB. Its been almost a month , hope all is well.

Thanks for all the support. Full pics on build soon!
Logged
Pages: [1]   Go Up
« previous next »