« previous next »
Pages: [1]   Go Down

Author Topic: Options for rear wheel for a kx 250 1989  (Read 2688 times)

0 Members and 2 Guests are viewing this topic.

Offline golash

  • Jr. Member
  • **
  • Posts: 37
Options for rear wheel for a kx 250 1989
« on: January 25, 2012, 10:01:16 AM »
Hi

I`m ready to install wheel bearings but I`m not certain I should even use the wheel assembly.
The spokes are frozen and 35 percent of them are loose. The holes that receive the nipples are
elongated, not all but quite a few. I`m wondering when Kawasaki changed the rear wheel specs.
I see a used wheel on ebay but its for a 1996. I could get a new rim and spokes and re-lace the wheel.
Is it a difficult process. Need some help from the experts.
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Options for rear wheel for a kx 250 1989
« Reply #1 on: January 25, 2012, 01:35:39 PM »
Here is the short story.
You can use:
89-02 KX125, KX250.
89-04 KX500.
89-94 KDX200.
Rim widths will be either 1.85 for the 125's or 2.15 for the bigger bikes.
Rim diameters will be either 18" or 19" depending on the year and model.
Long story:
Here is the hub info I have and what year's the book says they are for:
R-1213 ? GRAY ? 20MM AXLE - BRG TO BRG 130MM - ROTOR OD 220MM - ROTOR BC 6X ON 116MM ? 36 SPOKES ? book says it FITS 89 KDX200, KX125, KX250, KX500
R-1213 - GRAY - 20MM AXLE - BRG TO BRG 130MM - ROTOR OD 220MM ? ROTOR BC 6X ON 116MM ? 36 SPOKES - book says it FITS 90-94 KDX200, 90-96 KX125 KX250 KX500
R-1237 - GRAY - 20MM AXLE - BRG TO BRG 130MM - ROTOR OD 220MM - ROTOR BC 6X ON 116MM - SPROCKET BC 6X ON 150MM - book says it FITS  97-98 KX125 & 250, 97-04 KX500
R-1287 - GRAY - 20MM AXLE - BRG TO BRG 130MM - ROTOR OD 220MM - ROTOR BC 6X ON 116MM - SPROCKET BC 6X ON 150MM - book says it FITS 99-02 KX125, 250
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline golash

  • Jr. Member
  • **
  • Posts: 37
Re: Options for rear wheel for a kx 250 1989
« Reply #2 on: January 25, 2012, 02:00:21 PM »
Hi sandblaster

Now that's a answer. Thanks very much.
Barry
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Options for rear wheel for a kx 250 1989
« Reply #3 on: January 25, 2012, 03:57:53 PM »
No problem.
I have been collecting this stuff for a few years  :lol:
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline xCountryguy04x

  • Newbie
  • *
  • Posts: 3
Re: Options for rear wheel for a kx 250 1989
« Reply #4 on: February 28, 2012, 12:24:35 PM »
Sandblaster, what book do you speak of? Sounds like some reading material I need. I recently traded a ps3 for a 99 kx250 and you can tell....
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Options for rear wheel for a kx 250 1989
« Reply #5 on: February 28, 2012, 01:29:56 PM »
Hello.
By "the book" I am talking about what the factory part numbers show for interchange.
The measurements, Hub ID's, ect that I posted are taken from bikes I have parted out.
The info I have recorded can be found here:
http://oem-cycle.com/BikeIdentification.aspx
As you can see, some bikes I have a lot more info on then others.
I add new info almost every week.
If there is info that you need and you don't see it there, shoot me an email and I'll see what I can find for you.
Thanks.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.
Pages: [1]   Go Up
« previous next »