« previous next »
Pages: [1]   Go Down

Author Topic: 86 kx5 swingarm  (Read 3011 times)

0 Members and 1 Guest are viewing this topic.

Offline zskunk

  • Jr. Member
  • **
  • Posts: 18
86 kx5 swingarm
« on: March 04, 2011, 10:37:24 AM »
does anyone know what the measurement should be at on the bearings? my clymer book doesn't tell me and i don't think there right. someone had a bunch of washers in place where the dust seals should be ..
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 86 kx5 swingarm
« Reply #1 on: March 04, 2011, 12:13:07 PM »
For the wheel, from the outside to the outside of the bearings is approximately 144.5MM.
If you have the correct wheel it should be stamped R-1158 on the hub.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline zskunk

  • Jr. Member
  • **
  • Posts: 18
Re: 86 kx5 swingarm
« Reply #2 on: March 04, 2011, 12:30:46 PM »
so is this where the swingarm bearings should be set at with the dust seals in ? outside to outside?
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 86 kx5 swingarm
« Reply #3 on: March 04, 2011, 04:22:25 PM »
Oh, sorry, that is where the rear wheel bolts on.
Turns out I have a swing arm for a 86.
I'll try to get you some dimensions on Monday or Tuesday.
« Last Edit: March 04, 2011, 04:24:18 PM by sandblaster »
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline zskunk

  • Jr. Member
  • **
  • Posts: 18
Re: 86 kx5 swingarm
« Reply #4 on: March 05, 2011, 12:02:21 AM »
thanks sandblaster!!
Logged

Offline byron909

  • Full Member
  • ***
  • Posts: 91
Re: 86 kx5 swingarm
« Reply #5 on: March 05, 2011, 05:36:35 AM »
bearings are centered in each side
Logged
1984 cr500 1985 kx125 1999ktm300mxc
1986 cr500 1986 kx500 2013.5 ktm450 fe
1987 cr500 1994 kx500
1991 cr500 2000 kx125
1995 cr250 2008 kx500
1995 cr500
2003 cr250
2003 cr500
2008 cr500

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 86 kx5 swingarm
« Reply #6 on: March 07, 2011, 05:45:54 AM »
From the inside of one bearing to the inside of the other bearing should be approximately 4 5/8".
The bearings are centered.
Here is some other dimensions as well.

Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline zskunk

  • Jr. Member
  • **
  • Posts: 18
Re: 86 kx5 swingarm
« Reply #7 on: March 07, 2011, 08:26:51 AM »
thank you very much .. thats gr8 info .. that should be up on the how to list!!
Logged
Pages: [1]   Go Up
« previous next »