Author Topic: exaust leak at cylinder port  (Read 4279 times)

0 Members and 1 Guest are viewing this topic.

J.Patterson

  • Guest
exaust leak at cylinder port
« on: January 13, 2004, 03:14:43 PM »
I pulled off the pipe and found deep grooves in the right side cylinder exaust port where the o-rings seat. Is this common? Any recomendations for a fix.

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
exaust leak at cylinder port
« Reply #1 on: January 13, 2004, 04:26:45 PM »
Is the pipe mount under the tank still there? Has it been repaired? Chances are the pipe mount was broken - or is now - and was left that way for awhile. Doesn't take long...

Rick

  • Guest
exaust leak at cylinder port
« Reply #2 on: January 14, 2004, 05:16:17 AM »
When you install your pipe, smear on a liberal amount of black high temp silicon, right over both o-rings, and then shove the pipe into the exhaust port.  The grooves are caused by the pipe moving around.  Not only does the silicon restrict movement, it will also create a better seal than the o-rings and give you more bottome end throttle response.  

Rick

teamgreen500

  • Guest
exaust leak at cylinder port
« Reply #3 on: January 15, 2004, 11:39:01 AM »
You might need NEW O-Rings AND a NEW COPPER Ring. As these get worn they allow the pipe to move TOO Much in the cylinder port.

I change about every 60 hours (When I ring/top-end).

Manny

Rick

  • Guest
exaust leak at cylinder port
« Reply #4 on: January 16, 2004, 09:15:53 AM »
Wow, Manny, you rering the top end every 60 hours?  That would make be installing 10-12 top ends a year :shock: .  I usually do only three top ends a year, even with all the riding.

Rick

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
exaust leak at cylinder port
« Reply #5 on: January 16, 2004, 11:28:25 AM »
I follow the service limits :lol:

teamgreen500

  • Guest
exaust leak at cylinder port
« Reply #6 on: January 16, 2004, 11:30:33 AM »
Uh, guys...

Paul jumps outta pefectly good Aircraft; so, you might think a little when he implies..."Limits". :?  :shock:

Manny

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
exaust leak at cylinder port
« Reply #7 on: January 16, 2004, 02:21:35 PM »
:oops:

J.Patterson

  • Guest
thanks for the info.....
« Reply #8 on: January 17, 2004, 01:06:04 PM »
The pipe mounts are solid. The bike had been dumped on the left side and the pipe had been repaired. The bend at the port does not line up "just as it should". The copper crush washer is also toast. Good to find out about the black silicone. I thought it was spitting Bile at me outa spite. Darn thing has an attitude! As far as Paul jumping outa good planes, what can I say. It took 60+ jumps and a tree for me to figure it out. How I wish I had the K5 then. The Drop zones and pits on Bragg would be a blast to ride.

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
exaust leak at cylinder port
« Reply #9 on: January 17, 2004, 05:13:24 PM »
I also set to Sea on ships designed to sink :lol:

hooah!

teamgreen500

  • Guest
exaust leak at cylinder port
« Reply #10 on: January 20, 2004, 10:37:20 AM »
Oh Yeah, I forgot...

Paul's also a Dolphin... :lol:


Manny

Rick

  • Guest
exaust leak at cylinder port
« Reply #11 on: January 20, 2004, 11:44:06 AM »
Heck, stick that Dolphin on a 500 and shoot him out the back of a perfectly good airplane for a water landing in fifth gear pinned to get the hydroplaning going, and you got yourself a real nice piece of footage for Real TV...

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
exaust leak at cylinder port
« Reply #12 on: January 20, 2004, 04:05:44 PM »
Rick!
 :lol:  :lol:  :lol:  :roll:
Iceroad champion 2006,still 2007,even 2008 without a single race!

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
exaust leak at cylinder port
« Reply #13 on: January 20, 2004, 04:15:25 PM »
Ha! I MIGHT be up for that :lol:

Quote from: Rick
Heck, stick that Dolphin on a 500 and shoot him out the back of a perfectly good airplane for a water landing in fifth gear pinned to get the hydroplaning going, and you got yourself a real nice piece of footage for Real TV...