« previous next »
Pages: [1]   Go Down

Author Topic: Gasket sealer moose spacer  (Read 2326 times)

0 Members and 1 Guest are viewing this topic.

Offline sniper1

  • Full Member
  • ***
  • Posts: 238
Gasket sealer moose spacer
« on: May 13, 2011, 08:37:44 AM »
        I read through the moose spacer thread and didn't see where anyone used permatex or hightac to seal the gaskets and my 01 had a rad valve so it had it's own rubber gasket built right in and didn't need sealer.

        The moose spacer came with 2 gaskets one for between the engine and spacer and another for between the other side of the spacer and reed cage and I'm assuming no gasket is needed where the rubber on the boot meets the reed cage so 2 gaskets should do the trick the rubber boot should seal up nicely without a gasket unless I have it wrong but how did you guys do it? I did search the intake spacer thread with no luck on answering these questions so take it easy on me if it was there and I missed it :) I'll be waiting for the thumpin if I missed it and shall take it like a man.
Logged
Just an old guy that enjoys going fast, I was in the army for 6 years and bought my first K5 when I returned from basic training. I raced a yz60 from age 6 to 8  a kx80 from 8 to 12  a kx125 from 12-17 intermediate class on k5 which I've owned 3.

Offline greylynn

  • Jr. Member
  • **
  • Posts: 32
Re: Gasket sealer moose spacer
« Reply #1 on: May 24, 2011, 03:46:57 PM »
I installed my Moose spacer at the same time as upgrading to V-Force III reeds, so I used the gaskets that came with the spacer and reeds.  I figured there should be a gasket there because there was one there before....

Grey
Logged

Offline Camo

  • Jr. Member
  • **
  • Posts: 44
  • Dune Rider
Re: Gasket sealer moose spacer
« Reply #2 on: May 24, 2011, 06:59:27 PM »
No gasket is needed on the rubber side of the Rad Valve. There wasn't one when it was mated to the cylinder.
Logged
2000 KX500
2004 KFX 800 Turbo Nitrous
2004 KFX 800 Nitrous
2006 KVF 730 Nitrous
2005 KVF 700
2011 KTM SX450F
2008 KTM SX 144
2007 KTM SX 85
2011 KTM SX 65
2007 KTM SX 50 Senior Pro
2004 Suzuki RM 65 (Kawie)
2008 Victory Hammer
2006 CBR1000

Offline Friar-Tuck

  • Hero Member
  • *****
  • Posts: 1,827
  • \o/ Live Free or Die
Re: Gasket sealer moose spacer
« Reply #3 on: May 26, 2011, 05:37:12 PM »
A bit of overkill but...
  it works... :oops:  :-D

Logged
"The Truth Has No Agenda"

Offline sniper1

  • Full Member
  • ***
  • Posts: 238
Re: Gasket sealer moose spacer
« Reply #4 on: May 28, 2011, 06:45:06 PM »
       Thanks guys and sorry it took me so long to post back but I couldn't get on the site for some reason and polar bus pmed me on the best way to go and thanks for replying guys I appreciate it.

       I ended up just using the gaskets and cleaning the surfaces real good and it's been leak free and feels much better on the throttle response with boyeson pro reeds and the spacer between the carb and reed block instead of up against the jug and it's not just a sop feel I know the bike is performing better but I cleaned the carb and set my float bowl while I had it apart I have a video of the bike running down the street but don't know how to post it.
Logged
Just an old guy that enjoys going fast, I was in the army for 6 years and bought my first K5 when I returned from basic training. I raced a yz60 from age 6 to 8  a kx80 from 8 to 12  a kx125 from 12-17 intermediate class on k5 which I've owned 3.
Pages: [1]   Go Up
« previous next »