« previous next »
Pages: [1]   Go Down

Author Topic: what size is the nut that holds the needle in place in the slide?  (Read 3584 times)

0 Members and 1 Guest are viewing this topic.

Offline stujordan

  • Jr. Member
  • **
  • Posts: 41
what size is the nut that holds the needle in place in the slide?
« on: August 07, 2014, 01:02:11 PM »
what size is the nut that holds the needle in place on the slide?
Logged

Offline Foxx4Beaver

  • Hero Member
  • *****
  • Posts: 8,952
  • James Stewart DID NOT invent the scrub!!..JoJo
Re: what size is the nut that holds the needle in place in the slide?
« Reply #1 on: August 07, 2014, 01:59:01 PM »
6mm socket will do ya.
Logged
Excuse me, ma'am...but you've got extremely nice legs!!!...what time do they open???                                                                                                               https://www.youtube.com/watch?v=n8tCgN3aryQ

Offline stujordan

  • Jr. Member
  • **
  • Posts: 41
Re: what size is the nut that holds the needle in place in the slide?
« Reply #2 on: August 07, 2014, 02:04:53 PM »
Tried that but its rounding the head off...think it was too tight to begin with....im in trouble :(
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: what size is the nut that holds the needle in place in the slide?
« Reply #3 on: August 07, 2014, 02:47:34 PM »
Be sure to use a 6 point socket...
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline stujordan

  • Jr. Member
  • **
  • Posts: 41
Re: what size is the nut that holds the needle in place in the slide?
« Reply #4 on: August 07, 2014, 02:56:29 PM »
I was...read somewhere it is a 5.5mm...dude made the exact same mistake as me...he then hammered a 5.5mm 6 point onto the nut and got it out....try that tomorrow...wish me luck...
Logged

Offline Foxx4Beaver

  • Hero Member
  • *****
  • Posts: 8,952
  • James Stewart DID NOT invent the scrub!!..JoJo
Re: what size is the nut that holds the needle in place in the slide?
« Reply #5 on: August 07, 2014, 06:25:55 PM »
you can check this thread out...1st page is about the same problem you're having.

http://www.kxriders.com/forums/index.php/topic,7313.0.html

worst case, you might have to find a used slide, or new.
Logged
Excuse me, ma'am...but you've got extremely nice legs!!!...what time do they open???                                                                                                               https://www.youtube.com/watch?v=n8tCgN3aryQ

Offline Oblivious Maximus

  • Full Member
  • ***
  • Posts: 107
Re: what size is the nut that holds the needle in place in the slide?
« Reply #6 on: August 08, 2014, 02:47:01 AM »
 I had this problem last spring and posted a 5.5 mm socket fix over on thumper talk. If you try it be extremely careful handling the needle and slide. I managed to hold it in my hand and gently tap the 5.5 socket and short extension onto the damaged 6mm nut with a jewelers hammer. It actually went quite easily. Once it was removed I cleaned it up to 5.5mm with a Dremel tool and used anti seize to reassemble it. It all worked fine for me but if I ever sell it the next owner may be puzzled.

 
« Last Edit: August 08, 2014, 02:50:46 AM by Oblivious Maximus »
Logged
Where the Hell is "Easy Street" ?

Offline stujordan

  • Jr. Member
  • **
  • Posts: 41
Re: what size is the nut that holds the needle in place in the slide?
« Reply #7 on: August 08, 2014, 05:06:34 AM »
I did what u described....got it fixed...happy camper once more :)
Logged

Offline Oblivious Maximus

  • Full Member
  • ***
  • Posts: 107
Re: what size is the nut that holds the needle in place in the slide?
« Reply #8 on: August 08, 2014, 08:54:45 AM »

Good to hear you fixed it. There are some real wizards here, if you have problems just search, read, or ask. Usually someone's been there and done it.
Logged
Where the Hell is "Easy Street" ?
Pages: [1]   Go Up
« previous next »