« previous next »
Pages: 1 ... 3 4 [5]   Go Down

Author Topic: 500AF project  (Read 31743 times)

0 Members and 3 Guests are viewing this topic.

Offline The Flyin Hawaiian

  • Hero Member
  • *****
  • Posts: 597
Re: 500AF project
« Reply #60 on: September 10, 2011, 03:03:53 AM »
Looks great! What hose did you use for the right side coolant passage on the cylinder?
Logged
A couple of 03 and 04 KXs, a few YZs, 3 PE 400s, a DR and a TS.

Offline trim

  • Jr. Member
  • **
  • Posts: 43
Re: 500AF project
« Reply #61 on: September 10, 2011, 03:33:38 AM »
It's a heater hose off a 1990's ford van from the block to the heater core.... Best part it was free!!!!!
Logged

Offline SHLEPY

  • Big Member
  • Sr. Member
  • ****
  • Posts: 443
Re: 500AF project
« Reply #62 on: September 10, 2011, 04:30:40 AM »
what exact year i need one of them to
Logged

Offline trim

  • Jr. Member
  • **
  • Posts: 43
Re: 500AF project
« Reply #63 on: September 10, 2011, 05:40:49 AM »
I'll go look today
Logged

Offline trim

  • Jr. Member
  • **
  • Posts: 43
Re: 500AF project
« Reply #64 on: September 10, 2011, 06:23:57 AM »
Quote from: SHLEPY on September 10, 2011, 04:30:40 AM
what exact year i need one of them to
It's a 1991 Ford Econoline van 5.0L engine p/n 5015-05163592
Logged

Offline SHLEPY

  • Big Member
  • Sr. Member
  • ****
  • Posts: 443
Re: 500AF project
« Reply #65 on: September 10, 2011, 06:54:31 AM »
Too cool Trim thanks alot im just not ready to shell out the cash for the SH hoses till i get the bugs worked out
Logged

Offline Kiwi500

  • Newbie
  • *
  • Posts: 9
Re: 500AF project
« Reply #66 on: September 12, 2011, 10:58:04 PM »
Good to see some one run the coolant lines tha same as a 500 setup, could not understand why all the extra hoses used on other conversions.
Is the clearance not there on the right hand side engine coolant hose?? To hard to mod the pipe?? I plan to build one of these, but can't see the point of the U shape hose, looks like a air lock in the making ?!?!?
Bike looks mint but !!
Logged

Offline trim

  • Jr. Member
  • **
  • Posts: 43
Re: 500AF project
« Reply #67 on: September 14, 2011, 08:04:09 AM »
Quote from: Kiwi500 on September 12, 2011, 10:58:04 PM
Good to see some one run the coolant lines tha same as a 500 setup, could not understand why all the extra hoses used on other conversions.
Is the clearance not there on the right hand side engine coolant hose?? To hard to mod the pipe?? I plan to build one of these, but can't see the point of the U shape hose, looks like a air lock in the making ?!?!?
Bike looks mint but !!
The U shaped hose is similar shape to the Service Honda no problems with air locks so far 5 tanks of fuel through it already.There is no room beside the cylinder for the cast inlet I did not feel like cutting up my new pipe trying to fit it around the inlet flipping it upsidedown with a U hose saved fabbing time for me.Not saying someone could not come up with an idea to get rid of that hose.I have a Procircut pipe off my old 500 I will try fitting it this winter.
Logged
Pages: 1 ... 3 4 [5]   Go Up
« previous next »