« previous next »
Pages: 1 2 [3] 4   Go Down

Author Topic: I contacted Falicon about purchasing some knife rods.  (Read 17326 times)

0 Members and 2 Guests are viewing this topic.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #30 on: February 26, 2011, 10:33:55 AM »
My IMS rod arrived today.
Here is some general specs:



Thrust washer thickness is 1.0mm each. OD 41.6mm, ID 26.2mm.
The pin is 25.98mm OD, 13.95mm ID and is 54.4mm long.

« Last Edit: February 26, 2011, 10:37:10 AM by sandblaster »
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: I contacted Falicon about purchasing some knife rods.
« Reply #31 on: February 26, 2011, 07:03:26 PM »
sandblaster
Can you weight just the rod
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #32 on: February 26, 2011, 07:11:03 PM »
.55lb
How does that compare to a stock one?
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: I contacted Falicon about purchasing some knife rods.
« Reply #33 on: February 26, 2011, 07:26:02 PM »
9.8 oz.
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #34 on: February 27, 2011, 07:16:58 AM »
Very close.
Do you know what material the stock rods are made from?
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #35 on: March 09, 2011, 03:19:20 AM »
As an update I contacted Pauter Machine Co about making some Titanium rods.
We will see what they say.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #36 on: March 09, 2011, 03:41:13 AM »
Scratch that idea.
Here was their reply:

I'm sorry, we aren't able to make these for you.  Our forging does not allow for one-piece rods.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Motorrad

  • Guest
Re: I contacted Falicon about purchasing some knife rods.
« Reply #37 on: March 09, 2011, 06:22:56 AM »
Quote from: sandblaster on March 09, 2011, 03:41:13 AM
Scratch that idea.
Here was their reply:

I'm sorry, we aren't able to make these for you.  Our forging does not allow for one-piece rods.


Sad... very sad...  I wanted Nifty titanium parts.
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #38 on: March 09, 2011, 12:57:47 PM »
That would have been nifty.
We will see what the other companies say about the rods.
It may end up being semi nifty.  :-)
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline byron909

  • Full Member
  • ***
  • Posts: 91
Re: I contacted Falicon about purchasing some knife rods.
« Reply #39 on: March 09, 2011, 01:08:54 PM »
what about the hot rods brand? i had to buy one for my 86, at the time i could not find anything else. in the past i have used on other bikes, always thought they were good quality.
Logged
1984 cr500 1985 kx125 1999ktm300mxc
1986 cr500 1986 kx500 2013.5 ktm450 fe
1987 cr500 1994 kx500
1991 cr500 2000 kx125
1995 cr250 2008 kx500
1995 cr500
2003 cr250
2003 cr500
2008 cr500

Offline 1989kawasaki

  • Hero Member
  • *****
  • Posts: 1,017
  • my 89 cr250
    • youtube
Re: I contacted Falicon about purchasing some knife rods.
« Reply #40 on: March 09, 2011, 01:24:03 PM »
Quote from: byron909 on March 09, 2011, 01:08:54 PM
what about the hot rods brand? i had to buy one for my 86, at the time i could not find anything else. in the past i have used on other bikes, always thought they were good quality.

i know you are talking about using hot rods in a 500, but my crank rebuild with hot rods rod in my 250 is holding up very well,
i am impressed with it.
Logged
bikes

1977 RD400
1989 CR250
1988 CR500
1978 Z50
2009 Harley super glide custom

Motorrad

  • Guest
Re: I contacted Falicon about purchasing some knife rods.
« Reply #41 on: March 09, 2011, 01:30:43 PM »
K5+hotrod=kawablamo
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: I contacted Falicon about purchasing some knife rods.
« Reply #42 on: March 09, 2011, 01:43:51 PM »
Quote from: byron909 on March 09, 2011, 01:08:54 PM
what about the hot rods brand? i had to buy one for my 86, at the time i could not find anything else. in the past i have used on other bikes, always thought they were good quality.

I have seen good and bad with hot rod products but you have to consider what I see on a daily basis.
If I had no other choice I would use them.
However, they are re-building them in China.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline 1989kawasaki

  • Hero Member
  • *****
  • Posts: 1,017
  • my 89 cr250
    • youtube
Re: I contacted Falicon about purchasing some knife rods.
« Reply #43 on: March 09, 2011, 01:47:48 PM »
well they say that the hot rods are shot peened (whatever that means) does that make them any better?
Logged
bikes

1977 RD400
1989 CR250
1988 CR500
1978 Z50
2009 Harley super glide custom

Offline byron909

  • Full Member
  • ***
  • Posts: 91
Re: I contacted Falicon about purchasing some knife rods.
« Reply #44 on: March 09, 2011, 01:58:39 PM »
i remember seeing a made in tawain sticker on box. it is what it is i guess. i think they used to be better when owned by ims. all my parts looked nice, to help the whole deal was balanced. hopefully i never see a kawaboom or whatever from this.
Logged
1984 cr500 1985 kx125 1999ktm300mxc
1986 cr500 1986 kx500 2013.5 ktm450 fe
1987 cr500 1994 kx500
1991 cr500 2000 kx125
1995 cr250 2008 kx500
1995 cr500
2003 cr250
2003 cr500
2008 cr500
Pages: 1 2 [3] 4   Go Up
« previous next »