Author Topic: Reed Valves?  (Read 4013 times)

0 Members and 1 Guest are viewing this topic.

kawdude

  • Guest
Reed Valves?
« on: April 18, 2004, 02:11:46 PM »
All,
I need to replace the reeds in my bike and I'm wondering what is recommended.

I don't want to spend the money on Rad or Vforce assemblies.  I just want replacements for the stock ones.

Do any perform better than another?

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
Reed Valves?
« Reply #1 on: April 18, 2004, 02:16:28 PM »
Carbon Tech or Boysen Power reeds. The carbon fiber ones from Carbon tech will favor mid top end power and the ones from Boysen will favor the all around riders.

kawdude

  • Guest
Reed Valves?
« Reply #2 on: April 18, 2004, 02:22:43 PM »
Ok, Thanks!  Those were the ones that I was considering.  I noticed that those are "two stage" reeds.  Does that matter or will I need to change jetting after installing.

Is there a specific length of time that a reed lasts?

99KX500twofast

  • Guest
Reed Valves?
« Reply #3 on: April 18, 2004, 03:40:06 PM »
While we are on the subject of reeds, I have a few questions. Is the RAD valve worth the money? Has anyone tried it with the Moose torque spacer or should I just use the Moose spacer and install FMF torque reeds. And yes you guys are awesome!!! just replaced the fork seals and bushings on my 99K5 with help for this site. Also finishing rebuild on my sons 99KX60 with info from this site (centering crankshaft etc) Keep up the excellent work.

Folke

  • Guest
Re: Reed Valves?
« Reply #4 on: April 18, 2004, 05:40:57 PM »
Quote from: kawdude
All,
I need to replace the reeds in my bike and I'm wondering what is recommended.

I don't want to spend the money on Rad or Vforce assemblies.  I just want replacements for the stock ones.

Do any perform better than another?


Should you only change reeds  will recommend TDR-reeds this reeds is the best we have tryed, you can take reeds from CR 500 to KX 500 thats better.

kawdude

  • Guest
Reed Valves?
« Reply #5 on: April 19, 2004, 05:13:48 AM »
Thanks Folke!

When I replace these reeds do I need to loctite the screws in place?

Offline Paul

  • Hero Member
  • *****
  • Posts: 1,205
  • Top Dawg
    • KX Riders
Reed Valves?
« Reply #6 on: April 19, 2004, 06:29:29 AM »
Always, it's cheaper than the alternative ;)

Quote from: kawdude
Thanks Folke!

When I replace these reeds do I need to loctite the screws in place?

teamgreen500

  • Guest
Reed Valves?
« Reply #7 on: April 19, 2004, 08:50:38 AM »
As Paul said. I use fresh stockers most of the time; However, the Carbon Techs are real "Snappy" if you've got a pipe and ANY engine work.

Manny

Rick

  • Guest
Reed Valves?
« Reply #8 on: April 20, 2004, 08:56:00 AM »
I like the Carbon Fiber units from Boysen.  Kinda spendy, but I like the snap.  I've tried a lot of different reeds, but like these the best.

Rick

teamgreen500

  • Guest
Reed Valves?
« Reply #9 on: April 20, 2004, 04:01:49 PM »
I rest my case!

Manny