« previous next »
Pages: [1] 2   Go Down

Author Topic: look what i made at work  (Read 4308 times)

0 Members and 3 Guests are viewing this topic.

Offline seff23

  • Jr. Member
  • **
  • Posts: 24
look what i made at work
« on: September 15, 2010, 02:38:07 PM »
so i got got tired of breaking kickstarters so i fab'd up a steel one on my lunch break, its just a quickie one so i can ride this weekend, next week i'll go back and make a permanent one

Logged

Offline ktmdude

  • Full Member
  • ***
  • Posts: 96
Re: look what i made at work
« Reply #1 on: September 15, 2010, 02:49:16 PM »
Very cool. What do you for work?
Logged

Offline seff23

  • Jr. Member
  • **
  • Posts: 24
Re: look what i made at work
« Reply #2 on: September 15, 2010, 04:30:05 PM »
i work in a body shop
Logged

Offline Charlie500

  • Sr. Member
  • ****
  • Posts: 303
Re: look what i made at work
« Reply #3 on: September 15, 2010, 04:33:24 PM »
Bet you could sell em. Make a half dozen and post on the for sale section.... stock one cost over a hundred bucks I think
Logged
2014 KX 450 Bark-Buster

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: look what i made at work
« Reply #4 on: September 15, 2010, 04:50:59 PM »
Fot the life of me I don't know why no one has made a billet one yet.
Logged
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline seff23

  • Jr. Member
  • **
  • Posts: 24
Re: look what i made at work
« Reply #5 on: September 15, 2010, 04:56:29 PM »
Quote from: Charlie500 on September 15, 2010, 04:33:24 PM
Bet you could sell em. Make a half dozen and post on the for sale section.... stock one cost over a hundred bucks I think


yeah their pretty close, the last one i had to buy was $90 i only got $8 and about 30 minutes in this one...lol but when i do my permanent one i'm going to take my time and make it out of stainless so it looks nice and hopefully last forever..lol
Logged

Offline Charlie500

  • Sr. Member
  • ****
  • Posts: 303
Re: look what i made at work
« Reply #6 on: September 16, 2010, 02:06:59 AM »
Sounds cool man. Take a pic for us to see :roll:
Logged
2014 KX 450 Bark-Buster

Offline bempa

  • Jr. Member
  • **
  • Posts: 32
Re: look what i made at work
« Reply #7 on: September 16, 2010, 02:32:42 AM »
I hope it works ok. My experience is that any attempt using non cast fabrication for the kick it will twist slowly over time.
Logged

Offline Polar-Bus

  • Hero Member
  • *****
  • Posts: 1,023
Re: look what i made at work
« Reply #8 on: September 17, 2010, 08:49:57 AM »
Great thinking, but pray to god the weld at the base of the lever does not fail while kicking..... OUCH !   :-o
Logged
01' KX500
'84 GPz1100
'87 GSX-R  750
'06 HD Fatboy
'73 Kawi H1
'03 CRG KX500 Shifter kart

Offline bigbellybob

  • Sr. Member
  • ****
  • Posts: 261
Re: look what i made at work
« Reply #9 on: September 17, 2010, 09:29:04 AM »
Quote from: Polar-Bus on September 17, 2010, 08:49:57 AM
Great thinking, but pray to god the weld at the base of the lever does not fail while kicking..... OUCH !   :-o

i think it would bent before the weld would brake.
Logged
IF RIDING IS OUTLAWED ONLY OUTLAWS WILL RIDE

IF RIDING IS OUTLAWED ONLY OUTLAWS WILL RIDE

IF RIDING IS OUTLAWED ONLY OUTLAWS WILL RIDE

IF RIDING IS OUTLAWED ONLY OUTLAWS WILL RIDE

sponsor
http://www.steelmx.com/

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: look what i made at work
« Reply #10 on: September 17, 2010, 09:34:01 AM »
brian  what would the demand be for a billet kicker.
Logged

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: look what i made at work
« Reply #11 on: September 17, 2010, 11:32:01 AM »
Quote from: kaw rider on September 17, 2010, 09:34:01 AM
brian  what would the demand be for a billet kicker.
I think it would be pretty good demand. Kx500s are prone to braking the kicker. Also it would look cool, you could also make it 1/2' to 3/4' longer for more leverage.
Logged
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline Charlie500

  • Sr. Member
  • ****
  • Posts: 303
Re: look what i made at work
« Reply #12 on: September 17, 2010, 12:10:07 PM »
Quote from: kaw rider on September 17, 2010, 09:34:01 AM
brian  what would the demand be for a billet kicker.

I want one.... I would also be very interested in a billit two piece clutch cover....
Logged
2014 KX 450 Bark-Buster

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: look what i made at work
« Reply #13 on: September 17, 2010, 12:44:32 PM »
to do a nice clutch cover i think it will cost more then most people are willing to spend.
Logged

Offline junk man

  • Full Member
  • ***
  • Posts: 69
Re: look what i made at work
« Reply #14 on: September 17, 2010, 06:05:11 PM »
I broke two and then made a steel one. Is that cold roll steel ? i used a Honda XR500
kick starter i think there forged  well if it bends try try again

good luck JM
« Last Edit: September 17, 2010, 06:17:28 PM by junk man »
Logged
Pages: [1] 2   Go Up
« previous next »