Author Topic: cylinder scoring  (Read 2658 times)

0 Members and 1 Guest are viewing this topic.

Offline utahriding

  • Jr. Member
  • **
  • Posts: 14
cylinder scoring
« on: October 18, 2009, 02:02:44 PM »
hello everyone  I'm new to this site and i am hoping someone can help.

i have recently finished rebuilding my bike,  upon first start up(ran for about 10min. max) coolant was leaking from head. i pulled the cylinder and noticed some light scoring.  is this normal?


(new rod, piston, rings, cylinder replated)
« Last Edit: October 18, 2009, 05:56:33 PM by utahriding »

Offline Johnniespeed

  • Hero Member
  • *****
  • Posts: 575
  • The Thrill of Speed overcomes the fear of Death.
Re: cylinder scoring
« Reply #1 on: October 18, 2009, 02:29:59 PM »
Mine doesnt look like that, so I would say NOT normal. Why did it leak coolant ? Why did it score the walls ?
 John
Spring is here and the Mighty 500 wants to ride.
 2004 KX500 E16
 Michigan has the best groomed and mapped trail system, check out the Cycle Conservation Club of Michigan trail maps.

Offline utahriding

  • Jr. Member
  • **
  • Posts: 14
Re: cylinder scoring
« Reply #2 on: October 18, 2009, 04:26:22 PM »
cylinder needs resurfacing. thought it was ok since place that plated it didnt say anything or do it, but i guess they only replate.

as for the scoring i dont know what caused it was hoping to get answers here.

Offline hughes

  • Hero Member
  • *****
  • Posts: 1,923
    • Dirt Hammers
Re: cylinder scoring
« Reply #3 on: October 19, 2009, 07:37:21 AM »
I don't know if I would call that scoring. Looks to be very light stratches from dirt/debris. Give us more details about why the engine was rebuilt and what was rebuilt in the engine. I have seen that before and in some causes it's due to the cylinder not being cleaned before install. Once you get a fresh replate cylinder from a vendor always washer the cylinder in warm soapy water and use a brush to brush the cylinder to ensure you get all the grit out of the cross hatch.
Open Class 2-Stroke Kawasaki KX500
Yamaha 2005 YZ250
Richard Hughes
Dirt Hammers - Online Off-Road Journal
hughes@dirthammers.com
http://www.dirthammers.com

Offline utahriding

  • Jr. Member
  • **
  • Posts: 14
Re: cylinder scoring
« Reply #4 on: October 19, 2009, 09:14:47 AM »
repairs started as oil leak, and grew to full rebuild(all new lower end bearings, crank rebuilt with new wiesco rod, cylinder replated , new wiesco piston. didn't wash cylinder, figured it was ready to go when i got it back.   should it be honed again before reinstalling? should i get new rings? do you think any debris got washed into the lower end , and should it be cleaned out?
« Last Edit: October 19, 2009, 01:36:05 PM by utahriding »

Offline utahriding

  • Jr. Member
  • **
  • Posts: 14
Re: cylinder scoring
« Reply #5 on: October 21, 2009, 02:41:42 PM »
problem solved. coolant leaking into cylinder washing walls causing dry condition.

cylinder , head resurfaced , cylinder honed , new rings , new gaskets. TIME TO RIDE.

thanks for the help guys.

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: cylinder scoring
« Reply #6 on: October 21, 2009, 02:50:14 PM »
aceton will get most of the dirt out of the replate.