« previous next »
Pages: [1]   Go Down

Author Topic: V2 screws coming loose  (Read 3014 times)

0 Members and 1 Guest are viewing this topic.

Offline martinfan30

  • Sr. Member
  • ****
  • Posts: 456
  • 2000 KX500
V2 screws coming loose
« on: May 18, 2009, 03:48:21 AM »
I have been constantly thinking about if the screws on the V2 reeds ever work loose? Has anyone lost an engine due to ingesting a screw?
Logged
2000 KX500
2005 XR650L

Neither are stock, and both are great desert bikes.

stewart

  • Guest
Re: V2 screws coming loose
« Reply #1 on: May 18, 2009, 04:21:49 AM »
never heard off one coming out
Logged

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: V2 screws coming loose
« Reply #2 on: May 18, 2009, 07:02:50 AM »
I haven't heard of that. I have had mine for years and have not ever had a prob. The stock reeds have screws in them also. The screws on the V2 go into plastic, Do to the fact that the holes are unthreaded it acts like a nylock nut. I think the only way you would have something to worry about is if the screws have been taken in and out a whole bunch of times.
« Last Edit: May 18, 2009, 07:05:01 AM by BDI »
Logged
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: V2 screws coming loose
« Reply #3 on: May 18, 2009, 07:20:56 AM »
Like Brian is saying on the cylinder reed motor it not really a problem, but on the case reed motor it is a problem. Most guy will replace reeds once then get new cages after that. My buddy lost 5 motor because of the screws coming loose within  2 years. That why i don't run the v-2 in my motor, only V-3.
Logged

Offline cbxracer30

  • Sr. Member
  • ****
  • Posts: 304
Re: V2 screws coming loose
« Reply #4 on: May 18, 2009, 08:28:23 AM »
None of the guys I Know have had this problem.We've had reeds come apart and the only time I replaced my reed on the V2 I locktited the screws before replacing them. Blue locktite good stuff.CBX
Logged
Yep, you can ride it - if YOU can start it !!

Offline Johnniespeed

  • Hero Member
  • *****
  • Posts: 575
  • The Thrill of Speed overcomes the fear of Death.
Re: V2 screws coming loose
« Reply #5 on: May 18, 2009, 02:24:31 PM »
I have aways worried about reed screws coming loose too. So I have always  used lock-tite on those screws. Never had any come loose and hope to keep it that way.
 John
Logged
Spring is here and the Mighty 500 wants to ride.
 2004 KX500 E16
 Michigan has the best groomed and mapped trail system, check out the Cycle Conservation Club of Michigan trail maps.

Offline Polar-Bus

  • Hero Member
  • *****
  • Posts: 1,023
Re: V2 screws coming loose
« Reply #6 on: May 19, 2009, 03:58:58 AM »
Quote from: martinfan30 on May 18, 2009, 03:48:21 AM
I have been constantly thinking about if the screws on the V2 reeds ever work loose? Has anyone lost an engine due to ingesting a screw?

If I remember right, years ago when VF 2's came out, there was actually a recall on those (the screws were in fact loosening up). I believe that is why VF 2's were only on the market for a short while, then they came out with VF 3's. Might want to give a call to Moto Tassari, and get the specific details....
Logged
01' KX500
'84 GPz1100
'87 GSX-R  750
'06 HD Fatboy
'73 Kawi H1
'03 CRG KX500 Shifter kart

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: V2 screws coming loose
« Reply #7 on: May 19, 2009, 06:11:05 AM »
If thread is wornout in plastic,replace stock bolts with V-shaped and counterzink holes and place the nuts above (opposites) with nylonloc nut and loctite. :wink:

Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

Offline PowerFiend

  • Full Member
  • ***
  • Posts: 169
Re: V2 screws coming loose
« Reply #8 on: May 19, 2009, 07:19:25 AM »
If I remember from my RC car days, you shouldn't loctite into plastic. It makes the plastic soft. They use a bit of superglue instead.
Logged
Pages: [1]   Go Up
« previous next »