« previous next »
Pages: 1 [2]   Go Down

Author Topic: Kx500 motor in a streetbike chassis?  (Read 7384 times)

0 Members and 1 Guest are viewing this topic.

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: Kx500 motor in a streetbike chassis?
« Reply #15 on: May 02, 2009, 08:24:54 AM »
were they stock and 600cc. I raced acouple of 600 in quads on oval ice and with my 450 and half track they would start to pull away.

Maybe stewart or K5abuser can say in 1/4 mile race what would win. 600cc street bike or K5 with street rubber.
Logged

Offline k5abuser

  • Sr. Member
  • ****
  • Posts: 305
Re: Kx500 motor in a streetbike chassis?
« Reply #16 on: May 02, 2009, 12:56:00 PM »
thats just what me and stewart was talking about thursday . looking forward to the drag strip . just takes some time for me to get away . working as much as i can while i can . lol
Logged
race gas is fast but Q16 hauls azz.i still ride because i am not ready to have been that fast. i ride a kx500 because they don't make a kx600!ck k5abuser on youtube

Offline cbxracer30

  • Sr. Member
  • ****
  • Posts: 304
Re: Kx500 motor in a streetbike chassis?
« Reply #17 on: May 02, 2009, 01:32:00 PM »
My one hired gun, Ben took my K5 to Beaver Springs Raceway and could run right with my buddys 900rr 10.5's-10.4s I think his best pass was at Mason Dixon a 10.1 at 121mph thats gettin it done, No bars carrying the front wheel for 4 gears. Its gone 93mph in 500ft. CBX
Logged
Yep, you can ride it - if YOU can start it !!

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: Kx500 motor in a streetbike chassis?
« Reply #18 on: May 02, 2009, 02:10:03 PM »
In a 1/4 mile, my moneys on the K5 as I've already seen some beat 600 sportbikes.  With a good holeshot they have a tough time trying to run ya down!
Logged
America is all about speed. Hot, nasty, bad-ass speed.

Offline RoostDaddy

  • Sr. Member
  • ****
  • Posts: 445
Re: Kx500 motor in a streetbike chassis?
« Reply #19 on: May 02, 2009, 02:21:39 PM »
Paul,
I have a buddy that I used to race with that built a Banshee motor and mounted it into a RD 350/400 frame. (easy SWAP)
He ran a ZX9 fiberglass shell and that thing was not only trick looking but also very fast.  With these motors your combinations are endless.
Logged
America is all about speed. Hot, nasty, bad-ass speed.

Offline demographic

  • Hero Member
  • *****
  • Posts: 825
Re: Kx500 motor in a streetbike chassis?
« Reply #20 on: May 08, 2009, 11:34:28 PM »
Theres a chap who used to be on here who had a KX500 engine shoehorned into a Cagiva Mito 125 chassis, and theres been a few CR500/Cagiva Moto conversions as well.

This is a standard 125 Mito by the way as I assume that you lot over in the US don't get 125 two stroke road bikes
.
Logged
Pages: 1 [2]   Go Up
« previous next »