Author Topic: 02 KX 500 head gasket leak  (Read 6434 times)

0 Members and 3 Guests are viewing this topic.

Offline The Flyin Hawaiian

  • Hero Member
  • *****
  • Posts: 597
02 KX 500 head gasket leak
« on: January 23, 2008, 04:38:03 PM »
I have a question about a external coolant leak on a 02 KX 500. I am probably swapping my old DR350/435S for my brother inlaws KX 500. I noticed that it has a external coolant leak around the head gasket when running. It has the optional thicker head gasket. I had this same problem on my old 88 KX 500 also. It doesnt seem to be getting into the cyl. Anybody else experiance this? Cant wait to get it!
A couple of 03 and 04 KXs, a few YZs, 3 PE 400s, a DR and a TS.

stewart

  • Guest
Re: 02 KX 500 head gasket leak
« Reply #1 on: January 23, 2008, 05:10:53 PM »
toss the fiber thick gasket in trash and lap the head to be sure its flat put on a cometic steel gasket and some gray sealer around the water passeges and that will solve problem

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: 02 KX 500 head gasket leak
« Reply #2 on: January 23, 2008, 05:33:55 PM »
If you want it to leak some more then ignore what Stewart said. :wink:
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline KXcam22

  • Hero Member
  • *****
  • Posts: 1,677
Re: 02 KX 500 head gasket leak
« Reply #3 on: January 24, 2008, 04:38:58 PM »
I 3rd what Stewart said. Lap Lap Lap. Easy and works great.  I start by lightly lapping the head and barrel surfaces separately using #400 emery cloth taped to glass or a super flat steel plate. Then lap them to each other using valve grinding compound.  You will have to pull the head studs but don't skip doing the barrel because of it. The trick with lapping is to go slow with a twisting motion and inspect the surface frequently. You will watch the dull grey area grow as you lap.  Hope this helps. Cam.

ps if anyone has other methods I am all ears.

Offline mdw471

  • Full Member
  • ***
  • Posts: 149
    • Wolbrink Race
Re: 02 KX 500 head gasket leak
« Reply #4 on: January 25, 2008, 02:52:45 AM »
Great Idea!!

After you have lapped the head and barrel the first time, does it stay flat even after use? Or do you redo it everytime you change the piston?

Does the lappong correct a manufacturing short coming or does heat cycling the engine cause it to 'warp' out?!?

Mark
« Last Edit: January 25, 2008, 03:53:01 AM by mdw471 »
for more information about the World's Fastest Dirt Bike, www.wolbrinkrace.blogspot.com

stewart

  • Guest
Re: 02 KX 500 head gasket leak
« Reply #5 on: January 25, 2008, 04:45:56 AM »
Great Idea!!

After you have lapped the head and barrel the first time, does it stay flat even after use? Or do you redo it everytime you change the piston?

Does the lappong correct a manufacturing short coming or does heat cycling the engine cause it to 'warp' out?!?

Mark
proably some of both

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: 02 KX 500 head gasket leak
« Reply #6 on: January 25, 2008, 06:46:02 AM »
also when you install the stud, don't over tighten and put a 45* cut on the hole. so the aluminum doesn't roll up around the stud.

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: 02 KX 500 head gasket leak
« Reply #7 on: January 25, 2008, 12:00:25 PM »
also when you install the stud, don't over tighten and put a 45* cut on the hole. so the aluminum doesn't roll up around the stud.

           Very,very good advice on the stud thing.
   
     I never ever use emery cloth to lap things it roles up the edge of what ever you are trying to make flat. I use valve laping compound on a piece of glass on top of a piece of granit. I clamp it all down on the work bench with rubber jawed wood working clamps and use the old school figure eight method. I don't lap them together because I figure that if it's as flat as the sheet of glass then It's good. I have never had a problem with this method and I have fixed a bunch leaks on many different things.
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline The Flyin Hawaiian

  • Hero Member
  • *****
  • Posts: 597
Re: 02 KX 500 head gasket leak
« Reply #8 on: January 25, 2008, 12:24:31 PM »
Im not sure I understand the 45* cut. Are you basically chamfering the stud hole?
A couple of 03 and 04 KXs, a few YZs, 3 PE 400s, a DR and a TS.

Offline BDI

  • Hero Member
  • *****
  • Posts: 1,533
Re: 02 KX 500 head gasket leak
« Reply #9 on: January 25, 2008, 12:36:50 PM »
Im not sure I understand the 45* cut. Are you basically chamfering the stud hole?
    Yes if you don't the unthreaded portion of the stud mushrooms the deck around the studs if you screw the studs in  tight
Smoke every cigarette like It's your last and ride like you stole something!!!

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: 02 KX 500 head gasket leak
« Reply #10 on: January 26, 2008, 09:04:24 AM »
also depends on the head surface design.
when stewart cut my base it was .004" warped.