Author Topic: KX500 running problems  (Read 3702 times)

0 Members and 1 Guest are viewing this topic.

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
KX500 running problems
« on: November 23, 2007, 12:45:31 AM »
Hello,

I've had problems with idling, now my problem is a bit different. When I ride my kx500 with the choke off, it cuts out, runs very ruff and wants to die. Then I pull the choke up, the bike seems to run fine or a lot better.
I've to the point of just replacing the carb with a different one. If replacing is my only option. What all years interchange with the 1989 model PWK V461DB01?

Thank You,

Dan in Vacaville, Ca
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510

stewart

  • Guest
Re: KX500 running problems
« Reply #1 on: November 23, 2007, 12:54:25 AM »
doese your bike have a chrome slide in the carb or a gray slide and have you blown air thru pilot  jet  and what size pilot do you run

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
Re: KX500 running problems
« Reply #2 on: November 23, 2007, 01:05:46 AM »
The slide is gray. I'm not sure what size the jet is???
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510

stewart

  • Guest
Re: KX500 running problems
« Reply #3 on: November 23, 2007, 01:21:52 AM »
look for a newer chrome slide

Offline Polar-Bus

  • Hero Member
  • *****
  • Posts: 1,023
Re: KX500 running problems
« Reply #4 on: November 23, 2007, 06:46:27 AM »
Hello,

I've had problems with idling, now my problem is a bit different. When I ride my kx500 with the choke off, it cuts out, runs very ruff and wants to die. Then I pull the choke up, the bike seems to run fine or a lot better.
I've to the point of just replacing the carb with a different one. If replacing is my only option. What all years interchange with the 1989 model PWK V461DB01?

Thank You,

Dan in Vacaville, Ca

Sounds to me like you simply have a partially plugged pilot jet.
01' KX500
'84 GPz1100
'87 GSX-R  750
'06 HD Fatboy
'73 Kawi H1
'03 CRG KX500 Shifter kart

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
Re: KX500 running problems
« Reply #5 on: November 23, 2007, 09:50:57 AM »
Are you talking about the main jet, that is between the floats?

Sorry for my lack of knowledge

Dan in vacaville
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510

stewart

  • Guest
Re: KX500 running problems
« Reply #6 on: November 23, 2007, 10:32:34 AM »
no it take a small strieght screw driver and is down in a hole next to mian has to be blown out with compressed air

Offline tharden

  • Full Member
  • ***
  • Posts: 109
Re: KX500 running problems
« Reply #7 on: November 23, 2007, 10:56:32 AM »
Cleaning the Carb would be my choice, but I would also check the compression as well.  A two cycle engine can have these same symptoms when low on compression. 

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
Re: KX500 running problems
« Reply #8 on: November 23, 2007, 11:30:34 AM »
What should the cylinder compression be for a 1989 model?
I'm taking out the main pilot jet now.

Dan
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510

stewart

  • Guest
Re: KX500 running problems
« Reply #9 on: November 23, 2007, 04:05:42 PM »
around 140 psi

arleybeer40

  • Guest
Re: KX500 running problems
« Reply #10 on: November 26, 2007, 07:41:10 PM »
does it run ok though? i personally dont like my 2 stroke to idle. but to your problem, check what everyone else has said but you might want to also try a new spark plug and check your oil fuel mix.

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
Re: KX500 running problems
« Reply #11 on: November 27, 2007, 01:37:48 PM »
Yes, the bike runs great with the choke on, just when the choke is off it cuts out and dies. I'm having a local bike shop look at it now. He says its a main pilot jet. I will get the bike back this friday. Thanks for all the sugestions.

Dan in Vacaville
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510

crusty

  • Guest
Re: KX500 running problems
« Reply #12 on: November 28, 2007, 10:26:08 AM »
chances are your needle and seat are worn replace both my last baby was a 89 it took a long time to make her all new and pretty again but well worth it.

Offline dans89kx500

  • Full Member
  • ***
  • Posts: 82
Re: KX500 running problems
« Reply #13 on: December 01, 2007, 02:24:17 PM »
Well, my bike is finally fixed and running great (I took it for a ride today). The pilot jet was the problem, they replaced the 60 jet with a 65..... I do need now to replace a worn intake boot real soon. Anyway thanks for all the info. Great web site!

Dan in Vacaville
Daniel in Vacaville
1989 KX500
2000 Husaberg FC501
2009 Husqvarna TC510