« previous next »
Pages: [1] 2   Go Down

Author Topic: Lectron rings  (Read 6426 times)

0 Members and 3 Guests are viewing this topic.

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Lectron rings
« on: August 29, 2007, 10:22:08 PM »
What about these rings,have you tried them Steward or anyone who use Lectron? :|
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: Lectron rings
« Reply #1 on: August 30, 2007, 12:08:06 AM »
not enough room on the bike  to fit and i thought they were for more a 4 stroke set up to change velocty thru carb
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: Lectron rings
« Reply #2 on: August 30, 2007, 05:50:57 AM »
For me isn?t no problem with room, I will use KN-filters mounted directly on carb.
Get higher velocity is a good thing regardless of 2-stroke or 4-stroke isn?t it? :-D
I?m trying to test my Lectron next week,waiting for right needle though (4-2 XL),and see this ring at a website,maybe worth testing too. :|
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: Lectron rings
« Reply #3 on: August 30, 2007, 06:53:11 AM »
i have a 4.5" ring on a 41.5mm mikuni. and a nice intake manifold.
Logged

Offline YUNGGUNNAZ

  • Full Member
  • ***
  • Posts: 219
Re: Lectron rings
« Reply #4 on: August 31, 2007, 01:16:19 AM »
4-2xl.careful hero.thats gonna be lean compared to your old one(7-1). :-)
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: Lectron rings
« Reply #5 on: August 31, 2007, 04:46:45 AM »
Quote from: YUNGGUNNAZ on August 31, 2007, 01:16:19 AM
4-2xl.careful hero.thats gonna be lean compared to your old one(7-1). :-)

Ops!
That needle runs Steward with same ported barell and piston,but I got DOMA-pipe though.
Maybe to lean? :|

Fast by Gast recomend 7-1 needle for KX500 and now I?m unsure witch one I should pick
to start with :?

What do you think Steward? 8-)
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: Lectron rings
« Reply #6 on: August 31, 2007, 05:13:50 AM »
4.2 xl needle at around 2.010 long with 1 to 1.5 turns on power jet at 1000 feet elevtion with 50.1 hr1 belray and vp  cmp at 15 to 1  comp may take some adjusting with diffrent set up
Logged

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: Lectron rings
« Reply #7 on: September 01, 2007, 07:23:17 AM »
how do you guys bolt up a 44mm lectron to the intake manifold.
Logged

stewart

  • Guest
Re: Lectron rings
« Reply #8 on: September 01, 2007, 10:32:58 AM »
just lube it and  it goes right on
Logged

Offline YUNGGUNNAZ

  • Full Member
  • ***
  • Posts: 219
Re: Lectron rings
« Reply #9 on: September 02, 2007, 12:55:19 AM »
was the 4-2xl needle a packard needle or fast by gast one?
Logged

stewart

  • Guest
Re: Lectron rings
« Reply #10 on: September 02, 2007, 03:42:00 AM »
packerd .......there is a diffrence
Logged

Offline kaw rider

  • Hero Member
  • *****
  • Posts: 1,218
  • Cool your engine with water not fuel
Re: Lectron rings
« Reply #11 on: September 02, 2007, 07:12:10 AM »
bolt one of these carbs.
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: Lectron rings
« Reply #12 on: September 03, 2007, 11:01:46 PM »
Quote from: stewart on September 02, 2007, 03:42:00 AM
packerd .......there is a diffrence

What?s diffrence? :-o
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: Lectron rings
« Reply #13 on: September 04, 2007, 12:36:56 AM »
they say the tapers are diffrent on  needles from diffrent manufacters  even vary needle to needle
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: Lectron rings
« Reply #14 on: September 04, 2007, 11:01:54 PM »
Now you confusing me more then ever? :-D

The dealer is Packardracing,yeah?
Needles manufactures in different ways and mades
slighly different,I?m right? :|
I saw in packardracings website they fabricate Lectron needle in CNC-machines. :wink:

The Lectronrings adds +6cfm in velocity! :evil:
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!
Pages: [1] 2   Go Up
« previous next »