« previous next »
Pages: 1 2 [3]   Go Down

Author Topic: PORTING & POLISHING  (Read 12358 times)

0 Members and 1 Guest are viewing this topic.

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: PORTING & POLISHING
« Reply #30 on: March 19, 2007, 10:33:43 PM »
scotscooby,at my home! :-D

Steward,It?s real Backwheel power,I were there.... :-o

Can you again explain how much advance/reduce timing from stock and do you use stroboskop or measure?
Do you ovalbored fitting holes of ignitionplate to get right timing?
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: PORTING & POLISHING
« Reply #31 on: March 21, 2007, 01:35:06 AM »
 i have ground the timing slots longer towards the advance dirction but found the advance marks from kawasaki  to be about 3 degrees  and that was where i got my best results at 3 degrees advanced
Logged

brindle

  • Guest
Re: PORTING & POLISHING
« Reply #32 on: March 22, 2007, 01:44:54 PM »
stewart do you have a carb. to sale like you were talking about
are please tell me where i could find one please
Logged

Offline YUNGGUNNAZ

  • Full Member
  • ***
  • Posts: 219
Re: PORTING & POLISHING
« Reply #33 on: March 23, 2007, 01:11:35 AM »
try looking  on ebay for the lectron.also spell it electron.some people spell it wrong.if you don't find a 44mm then get a 40mm and have it bored.with or without power jet is a option for tuning.newer style is preferred because of metering rod change.
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: PORTING & POLISHING
« Reply #34 on: March 25, 2007, 05:46:21 AM »
Here is a Lectron.
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: PORTING & POLISHING
« Reply #35 on: March 25, 2007, 02:52:55 PM »
WHAT SERIES OF  needles is used in that lectron  x  or xl or  plian
Logged

Offline doordie

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 775
  • Do or Die.....
Re: PORTING & POLISHING
« Reply #36 on: March 26, 2007, 06:18:07 AM »
Quote from: stewart on March 25, 2007, 02:52:55 PM
WHAT SERIES OF  needles is used in that lectron  x  or xl or  plian

Steward,the needle is 3-1 XL ,what do you suggest I should start with on 99 oktan (not oxygenated fuel) but tuned bike. :?

Lectron says 7-1 XL on a stock KX500 seems rather wrong to yours 4-1 XL. :|
Logged
Iceroad champion 2006,still 2007,even 2008 without a single race!

stewart

  • Guest
Re: PORTING & POLISHING
« Reply #37 on: March 26, 2007, 10:33:57 AM »
my needle  is  x l 4.2  at  2.010  lenght  with power jet turned off  its fast
Logged
Pages: 1 2 [3]   Go Up
« previous next »