Author Topic: Best Crank Bearing Maker ? Use of Crank alignment tool?  (Read 2712 times)

0 Members and 1 Guest are viewing this topic.

IridiumRed

  • Guest
Best Crank Bearing Maker ? Use of Crank alignment tool?
« on: December 13, 2005, 02:47:35 AM »
Hey Guys

I'm going to be rebuilding my KX500 again First time I rebuilt it the crank was w/ out of true.... quickly wiped the main bearings.  So, sent the crank off to Arizona, got it trued / rebalanced.  Excited to see how it will run with the rebalanced / trued crank!!

Anyways,

Who do you guys think makes the best crank bearings?

Also, there is a crank alignment / installation tool - the wedge shaped tool that slides between the crank counterweights, so you can press the crank into the righthand case w/o disturbing the crank alignment

Do you guys ever use that?  I know that if you freeze the crank, and put the RH case in the oven (with the bearing installed of course), the two go together fairly easy, but I've got a press, and I thought about doing the freeze / heat process but still using the press to install the crank in the RH case... so I'd need that tool

Is it worth the extra hassle doing it that way?  Seems to me that anything that can be done to ensure crank alignment would be a GOOD thing

thanks!!
IR

Offline gowen

  • Resident Newbie
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1,350
  • www.KXRiders.com
RE: Best Crank Bearing Maker ? Use of Crank alignment tool?
« Reply #1 on: December 14, 2005, 05:14:45 AM »
To each his own on the bearings and how to install the crank. I have always used Wiseco rods and bearings. No problems.ever. I've lost a few rods and they were replaced with wiseco and have lasted and have never needed replacement. I install my cranks with a rubber hammer, just throw the crank in the freezer for a day or so, and it usally drops in without many issues, may need a light tap with a hammer. But my alignment is fine on all my bikes and that is the way I've done them all.

IridiumRed

  • Guest
I meant main bearings for the crank, not big-end rod bearing
« Reply #2 on: December 14, 2005, 06:13:11 AM »
Maybe I should have been a little more specific, I was asking about the main bearings that go into the case that support the crank

-sb

Offline KXcam22

  • Hero Member
  • *****
  • Posts: 1,677
RE: I meant main bearings for the crank, not big-end rod bea
« Reply #3 on: December 14, 2005, 09:39:57 AM »
IR,
  NSK, SFK, FAG.  If you go to a bearing house you can get quality bearings. Avoid the chinese ones, the metalurgy just isn't the same. Cam.

edkx

  • Guest
RE: I meant main bearings for the crank, not big-end rod bea
« Reply #4 on: December 14, 2005, 02:13:55 PM »
I don't mean to hi-jack this thread but has anyone ever used ceramic bearings.A few issues ago in DIRTBIKE, a guy used them in his YZ250 and claimed it revved a little quicker and vibrated less.

Offline Johnniespeed

  • Hero Member
  • *****
  • Posts: 575
  • The Thrill of Speed overcomes the fear of Death.
RE: I meant main bearings for the crank, not big-end rod bea
« Reply #5 on: December 15, 2005, 07:49:34 AM »
Edkx, do you know how they are constructed ? Are the steel races coated with ceramic? Are the Steel balls coated with ceramic ?   I have heard of turbo chargers using ceramic bearings, but I am not familiar with this yet.   I hope there are guys who can post the information. Does the lubrication require anything different ? Does the ceramic ever crack or peel ?
Spring is here and the Mighty 500 wants to ride.
 2004 KX500 E16
 Michigan has the best groomed and mapped trail system, check out the Cycle Conservation Club of Michigan trail maps.

edkx

  • Guest
RE: I meant main bearings for the crank, not big-end rod bea
« Reply #6 on: December 15, 2005, 01:54:08 PM »
To quote the fellow in the sept.2005 issue"The crank bearings get replaced with Power Spin ceramic bearings.I know the same place I get them from,TKO development,supplies them to many of the factories for their race bikes.The engine does rev up a bit quicker but the main reason I use them is because they really reduce vibration.That's a big plus over the course of a race."

moburki

  • Guest
RE: I meant main bearings for the crank, not big-end rod bea
« Reply #7 on: December 16, 2005, 04:39:05 AM »
The balls themselves are ceramic afaik.