« previous next »
Pages: [1]   Go Down

Author Topic: Is this normal?  (Read 2070 times)

0 Members and 1 Guest are viewing this topic.

Offline Bcsnowbiker

  • Jr. Member
  • **
  • Posts: 34
Is this normal?
« on: May 14, 2019, 04:04:36 PM »
Never seen a clutch were the plate tabs have 10mm + of clearance from the basket fingers.
Logged

Offline Bcsnowbiker

  • Jr. Member
  • **
  • Posts: 34
Re: Is this normal?
« Reply #1 on: May 14, 2019, 04:07:24 PM »
I know this isn't normal :cry:
Logged

Offline Bcsnowbiker

  • Jr. Member
  • **
  • Posts: 34
Re: Is this normal?
« Reply #2 on: May 14, 2019, 04:18:44 PM »
I have seen worse baskets but I have never seen an inner hub this notched.
In my eyes it is from the excessive tab clearance on the basket.
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Is this normal?
« Reply #3 on: May 15, 2019, 02:54:49 AM »
Lol... No, it's not normal.... Someone has machined the basket a lot...
If you use it you will breaking a ton of plates...
You need to replace that basket and hub.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline Bcsnowbiker

  • Jr. Member
  • **
  • Posts: 34
Re: Is this normal?
« Reply #4 on: May 15, 2019, 03:31:33 AM »
Makes sense but never thought someone would go beyond simple filing.
I already ordered a prox basket and inner hub last night.
Recommendations on plates and springs?
When I did up my rm250 motor I had issues finding plates/springs that didn't slip.
In the end wiseco were the best with Barnett springs but they are not available for the kx.
I was thinking of going with the Barnett Kevlar plates.
Logged

Offline motorman455

  • Full Member
  • ***
  • Posts: 118
Re: Is this normal?
« Reply #5 on: May 15, 2019, 04:13:19 AM »
Rekluse offers their torq drive plates and even auto clutch now. The plates alone are supposed to handle a lot more torque but they are pricey. They also come with stainless steel basket inserts to prevent the groove wear.
Logged

Offline Bcsnowbiker

  • Jr. Member
  • **
  • Posts: 34
Re: Is this normal?
« Reply #6 on: May 15, 2019, 05:51:57 AM »
Quote from: sandblaster on May 15, 2019, 02:54:49 AM
Lol... No, it's not normal.... Someone has machined the basket a lot...
If you use it you will breaking a ton of plates...
You need to replace that basket and hub.
Well you nailed that one. You can see 2mm was taken from one side of each of the fingers.
I would not even think that someone would do that in some bizarro world but I guess you've seen it all  :-o
I have watched all your videos BTW and read most anything you've posted here and on kxguru. You are a wealth of knowledge, thanks for your efforts 👍
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Is this normal?
« Reply #7 on: May 15, 2019, 11:51:38 AM »
I still have much to learn... But what I have learned, a lot of it came from this site and members that no longer visit  :cry:
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.
Pages: [1]   Go Up
« previous next »