Author Topic: 2016 Pumpkin seed build...  (Read 149527 times)

0 Members and 5 Guests are viewing this topic.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #225 on: November 08, 2018, 11:51:44 AM »
That's funny. I just got the Ti Powercore 2.1 yesterday and am doing the same thing! I removed both brackets and am going to rivet just the rear one back on in the proper location and put rivets back into the original holes. It has a 30mm inlet pipe vs the 32mm on the k5 (28 and 30mm id's  respectively). I cut the inlet pipe off 1" from the silencer and have a straight section of 32mm od pipe from my scalvini pipe which slips right over the silencer inlet. The people at FMF were totally useless and wouldn't bother to even give me the dimsions of the few that they carry for modern 2 strokes so it was trial and error to find one close. I tried the YZ250 one first but it was only a 28mm inlet pipe.

Be sure to document what you did.
I'm sure there are a few guys that might want to copy you  8-)
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #226 on: November 11, 2018, 10:10:39 AM »
I'm putting the races back in the frame.
I don't have any special tooling  :|
But, I do have a old 2" trailer hitch ball that is a nice fit  :lol:



Good old ACME  :mrgreen:

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline dave916

  • Hero Member
  • *****
  • Posts: 546
Re: 2016 Pumpkin seed build...
« Reply #227 on: November 11, 2018, 09:25:12 PM »
I'm putting the races back in the frame.
I don't have any special tooling  :|
But, I do have a old 2" trailer hitch ball that is a nice fit  :lol:



Good old ACME  :mrgreen:


You dont want be hammering the bearing race surface :-o :-D

Reduce the outer diameter of ur old bearing outer race{grind it } and use up side down to tap the new bearing race home /cool the bearing will also help

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #228 on: November 12, 2018, 03:34:30 AM »
Excellent suggestion but..... I removed brand new races so there was no need to order more, and grind the old set down as I am reusing the new stock races that I removed.
Further, I should have taken a pic while I was doing it... I put a rag under the ball... Just one layer...
The pic I posted was after I had done the deed and then decided I should post it but I couldn't find what I did with my clean rag..
I knew if I put a dirty rag in there people would freak  :lol:
I have done this same procedure many times over the years with no issues.
Then again, I don't beat the race up.
If you look at that hammer, it's very small and light.
I'll take a pic of the bearing surface later, as you will see this method does not damage the bearing surface in any discernible way.
I have done this same procedure and ran the races and bearings for over 15 years in the past so I'm sure these will outlast me and my bike riding days.  :-o
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #229 on: November 12, 2018, 03:53:57 AM »
The top clamp is being replaced as soon as I get it.
I put this top clamp on to hold it together.
Also, I'm replacing the bolts with Ti  8-)

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #230 on: November 25, 2018, 09:54:54 AM »
Mocking up the front end..



A little more Ti..

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline Brute

  • Hero Member
  • *****
  • Posts: 862
  • 787 ZA005 GE
Re: 2016 Pumpkin seed build...
« Reply #231 on: November 26, 2018, 05:53:10 AM »
What a beautiful bike and build!
I keep looking at KX500's but at 64 with the damage I have another KX500 is out of the picture. Really slowing down these days. Gives me a chance to take in more scenery!
As has been said, the first real scratch or damage will be a downer, but once it happens it will be over. Not that you will neglect it after that, it's always that 'first' one that really hurts.
Things Are More Like They Are Today Then They Have Ever Been Before...

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #232 on: November 26, 2018, 08:30:45 AM »
What a beautiful bike and build!
I keep looking at KX500's but at 64 with the damage I have another KX500 is out of the picture. Really slowing down these days. Gives me a chance to take in more scenery!
As has been said, the first real scratch or damage will be a downer, but once it happens it will be over. Not that you will neglect it after that, it's always that 'first' one that really hurts.

That's why I hope one of the wrecking crew at MXA does it first..
Then I can have them sign the damage and I'll clear coat it  :-D
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #233 on: November 26, 2018, 10:26:46 AM »
TSR's stuff is absolutely amazing...





The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline reklessj

  • Hero Member
  • *****
  • Posts: 921
Re: 2016 Pumpkin seed build...
« Reply #234 on: November 26, 2018, 06:33:01 PM »
TSR's stuff is absolutely amazing...






Yeah it's friggin beautiful, if I had the 9 bills right now I would be going that route. Although I'm not real fond of the polished bling
My rides: 1994 KX500, 1988 T4, 1998, ZXI 1100 JETSKI, 2003 MOUNTAIN CAT 900
WIFES (Baby Fiver) rides: 2004 KTM 105SX,1992 LT250R, 1995 ZXI 900 JETSKI,  2011 RMK 600
SONS ride: 1995 YZ125,2002 RM 250
other rides: 2007 RMZ450 RC Ediition, 2003 RMK700

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #235 on: December 10, 2018, 08:20:07 AM »
More goodies showed up today from Hammerhead.
I have used Hammerhead products for many years.
Everything has always been top quality.
These parts are no exception.
The shift lever is for a KX500 and has a 20mm extended tip.
Makes it nice for those with a larger shoe size  :-D
The rear brake lever is another sweet piece for the 2016 KTM 250 SXF chassis.
Looks and fits great.
The tip is Titanium so for those with weight reduction in mind this is a perfect match 8-)
https://hdmoto.com/
Thank you Hammerhead!

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline umberto

  • Administrator
  • Hero Member
  • *****
  • Posts: 2,488
  • First Ride 02-02-19
Re: 2016 Pumpkin seed build...
« Reply #236 on: December 10, 2018, 09:52:14 AM »
TSR's stuff is absolutely amazing...






Are there any other modifications you have to do to run the Boyesen Super Cooler besides the TSR clutch cover?  What do those guys run?
Perhaps I have a dirt bike addiction?

03 KX 250/88 KX 525/2017 KX250F - Goliath
17 KX250F/04 KX250
04 KX 250 - Lunchbox's Bike
05 KX 125/144

Offline motorman455

  • Full Member
  • ***
  • Posts: 118
Re: 2016 Pumpkin seed build...
« Reply #237 on: December 10, 2018, 11:30:54 AM »
I just received my TSR 2 piece right side cover and it was $805 USD delivered. It comes with the Boyeseen water pump, a pump to cylinder coolant hose (blue or green) and a new cylinder hose fitting. I got the one for the stock side location vs the rear cylinder relocation one.  It also came with the new clutch cover gasket and Allen screws for  the clutch cover and the water pump. The pump appears to be for a 94-04 KX250

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #238 on: January 09, 2019, 04:55:30 PM »
I really like WPC Treatments, Micro-polishing, ect ect...
But I'm going old school and polishing my own parts the hard way





The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: 2016 Pumpkin seed build...
« Reply #239 on: January 14, 2019, 04:22:46 PM »
Oh yeah... KX500 goodness... with Troy at TSR Products...

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.