Author Topic: Recommended frame mods/gusseting '90-04 ?  (Read 6641 times)

0 Members and 1 Guest are viewing this topic.

Offline joko

  • Full Member
  • ***
  • Posts: 62
Recommended frame mods/gusseting '90-04 ?
« on: December 07, 2014, 06:21:28 AM »
I've got my '90 & '95 frames stripped and am wondering if there are any existing welds that should be completed, or any gusseting added or add a weld in skid plate to reduce flex or add rigidity? Will be using for MX and am wondering if any frame mods would reduce flex, vibration and maybe prove improve cornering?

Offline dave916

  • Hero Member
  • *****
  • Posts: 546
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #1 on: December 07, 2014, 08:54:46 AM »
From rjhansens' photobucket
Destry Abbott's 2004 KX500_1







Offline joko

  • Full Member
  • ***
  • Posts: 62
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #2 on: December 07, 2014, 09:03:40 AM »
Other than the post welded on for the steering damper and the guard added for the water pump protection, I don't see any difference from the stock frame at the steering head nor the area near the head stay. Am I missing something?

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #3 on: December 07, 2014, 12:33:40 PM »
The t-mount where the sub-frame bolts on is gusseted, the rad tabs are reinforced, the mount between the upper exhaust mount tab and aft rad mount are tied together.  There is not a pic but the lower RH pipe mount tab is gusseted too.  There is  also gusseting on the subframe.









"Let there be light"

Offline joko

  • Full Member
  • ***
  • Posts: 62
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #4 on: December 07, 2014, 02:06:27 PM »
Ok, no major structural mods then?

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #5 on: December 07, 2014, 02:39:56 PM »
nope
"Let there be light"

Motorrad

  • Guest
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #6 on: December 07, 2014, 02:44:55 PM »
Re welds all around.    On factory bikes

Offline joko

  • Full Member
  • ***
  • Posts: 62
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #7 on: December 07, 2014, 02:52:07 PM »
I'm tempted to weld a stainless skid plate on (.035 wall) and add material to
motor mounts...

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #8 on: December 07, 2014, 03:45:06 PM »
motor mount don't really break, there are a few good aftermarket skid plates out there
"Let there be light"

Offline joko

  • Full Member
  • ***
  • Posts: 62
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #9 on: December 07, 2014, 03:51:00 PM »
Thinking of welding on a skid plate to gain rigidity
vs a bolt-on

Offline dave916

  • Hero Member
  • *****
  • Posts: 546
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #10 on: December 07, 2014, 10:05:54 PM »
The supermoto guys seem to brace the the sump guard area of frame
Have a look at second picture  tubing X bracing sump area
http://www.ktmforum.co.uk/supermoto/75177-2-stroke-wins-german-championship-race-s2-%3B.html

I have a cr500af gen 1 with a welded sumpguard ,easy enough to do with square tubing
Not sure if it help vibration

Good tip on any bracing weld here
http://www.dropbox.com/s/obazkrio1t...s%20Design.pdf

 really interest it bracing the frame in the motor are would help dampen vibration?

Offline ID KX500

  • Hero Member
  • *****
  • Posts: 626
  • Life, Liberty, and The Pursuit of Happiness
Re: Recommended frame mods/gusseting '90-04 ?
« Reply #11 on: December 07, 2014, 10:46:43 PM »
You mentioned cornering ',,,,I don't have one but there is a better dogbone made by Emig I think.
"Endeavor to persevere."