« previous next »
Pages: [1] 2   Go Down

Author Topic: What elase should I replace when splitting the case?  (Read 10062 times)

0 Members and 2 Guests are viewing this topic.

Offline dinkyguitar

  • Full Member
  • ***
  • Posts: 243
What elase should I replace when splitting the case?
« on: May 05, 2014, 06:44:05 AM »
Hi All,

I need to replace my crankshaft on my 87 KX 250.

What other bearings should I replace, other than the crankshaft bearings & seals, while I have the case split.

I checked all the bearings and they look good...even the ones on the outside (governor & water pump bearing)



What about those bushings that hold the needle bearings on the transmission shafts? Should those be replaced if I'm using another used transmission? BTW, one of the bears came off with the crank when I split the case. That's why it's missing from the crankcase.







dinky,
Logged

Offline Foxx4Beaver

  • Hero Member
  • *****
  • Posts: 8,952
  • James Stewart DID NOT invent the scrub!!..JoJo
Re: What elase should I replace when splitting the case?
« Reply #1 on: May 05, 2014, 09:16:01 AM »
if you're gonna do it...do it right, do it one time.
replace every bearing and every seal...replace every snap ring...don't half-a$$ it...there's nothing worse than rebuilding a bottom end/engine, just to have it fail shortly after because you skimped out on something, then have to tear it all back down and start from scratch.
don't assume a bearing is good just by "look"....that's where you'll get bitten!...plus, it's best to keep everything uniformly new!

you can save a small fortune by going to your local bearing shop for all your bearings.

check all the gears/forks/shafts/drum, replace anything that looks questionable...I know there's more, but I'm 9 beers deep right now and still dumpin em down....so I'm sure some of the other guys can add to the list.
« Last Edit: May 05, 2014, 09:26:21 AM by Foxx4Beaver »
Logged
Excuse me, ma'am...but you've got extremely nice legs!!!...what time do they open???                                                                                                               https://www.youtube.com/watch?v=n8tCgN3aryQ

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: What elase should I replace when splitting the case?
« Reply #2 on: May 05, 2014, 10:42:09 AM »
+1  8-)
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline reklessj

  • Hero Member
  • *****
  • Posts: 921
Re: What elase should I replace when splitting the case?
« Reply #3 on: May 05, 2014, 11:47:17 AM »
Absolutely replace all bearings and seals  while you have it apart and have peace of mind
Logged
My rides: 1994 KX500, 1988 T4, 1998, ZXI 1100 JETSKI, 2003 MOUNTAIN CAT 900
WIFES (Baby Fiver) rides: 2004 KTM 105SX,1992 LT250R, 1995 ZXI 900 JETSKI,  2011 RMK 600
SONS ride: 1995 YZ125,2002 RM 250
other rides: 2007 RMZ450 RC Ediition, 2003 RMK700

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: What elase should I replace when splitting the case?
« Reply #4 on: May 05, 2014, 11:51:31 AM »
Get crazy with clean up while your at it...
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: What elase should I replace when splitting the case?
« Reply #5 on: May 05, 2014, 11:57:51 AM »
And... Lap all the mating surfaces...

Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline dinkyguitar

  • Full Member
  • ***
  • Posts: 243
Re: What elase should I replace when splitting the case?
« Reply #6 on: May 05, 2014, 01:24:33 PM »
Yep...that's the way I'm leaning right now...replacing everything I can so I don't have to split the cases.

So, I got this bike for free. The clutch looks new, the cylinder still has the cross hatching, and the piston also looks good. Keep in mind this bike sat for 8 years in a shed, so I'm planning on looking at everything.

I have the service manual and already started measuring the clutch disk and metal plates. The clutch looks new and they all measure within the "new" specifications.

This bike could be a good project to restore since it's a 1987 model.

The way I look at it, if I spend even up to $1500.00, I will literally have a new bike. If I bought a 250 for $1500.00, (if there are any for that price) I would still not know what condition it was in, and will probably have to replace a part or two in the future.

By ripping the bike completely apart like I'm doing, at least I know what it looks like inside.

dinky,
Logged

Offline queen of spodes

  • Sr. Member
  • ****
  • Posts: 287
Re: What elase should I replace when splitting the case?
« Reply #7 on: May 08, 2014, 06:15:36 AM »
Are there bearing pullers for these smallish bearings circled in this photo?   I have some in my 89 KX125 that also need replacing.


Logged

Offline dinkyguitar

  • Full Member
  • ***
  • Posts: 243
Re: What elase should I replace when splitting the case?
« Reply #8 on: May 08, 2014, 07:58:53 AM »
Quote from: queen of spodes on May 08, 2014, 06:15:36 AM
Are there bearing pullers for these smallish bearings circled in this photo?   I have some in my 89 KX125 that also need replacing.


I was curious how I was going to remove these too... :?

dinky,
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: What elase should I replace when splitting the case?
« Reply #9 on: May 08, 2014, 10:24:50 AM »
You need a blind bearing puller.

Here's some pics and how they work:
http://www.oem-cycle.com/forum/viewtopic.php?f=39&t=64

I bet you can rent one from your local auto parts house.
Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline dinkyguitar

  • Full Member
  • ***
  • Posts: 243
Re: What elase should I replace when splitting the case?
« Reply #10 on: May 08, 2014, 11:34:03 AM »
Cool tool, but probably expensive....

Now that I've seen that, I could probably fabricate something out of an anchor bolt from home depot.

dinky,
Logged

Offline queen of spodes

  • Sr. Member
  • ****
  • Posts: 287
Re: What elase should I replace when splitting the case?
« Reply #11 on: May 08, 2014, 02:57:32 PM »
They have 5-piece blind pullers on ebay for $50 free shipping but I'm wondering if the MP one has smaller collets for our KX engines............
Logged

Offline Pmcg

  • Sr. Member
  • ****
  • Posts: 352
Re: What elase should I replace when splitting the case?
« Reply #12 on: May 08, 2014, 04:07:37 PM »
My cheap eBay set wouldn't get the power valve bearing or the clutch lever bearings.
Logged

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: What elase should I replace when splitting the case?
« Reply #13 on: May 08, 2014, 05:00:47 PM »
The only one on the K5 that I can't get with the MP is the lower clutch arm bearing as it isn't long enough.
But you can make a extension for it like alward25 did

Logged
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline alward25

  • Hero Member
  • *****
  • Posts: 1,349
Re: What elase should I replace when splitting the case?
« Reply #14 on: May 09, 2014, 02:00:04 AM »
My puller Is for rent for the price of shipping, just need to know which bearings you want to pull so I can be sure to have the right size puller.
Logged
"Let there be light"
Pages: [1] 2   Go Up
« previous next »