Author Topic: HRC Works bike crank  (Read 7203 times)

0 Members and 1 Guest are viewing this topic.

Offline PJSMAN

  • Jr. Member
  • **
  • Posts: 24
HRC Works bike crank
« on: October 08, 2013, 08:10:55 PM »
Has anyone tried this mod on a KX 500 crank?
this is a picture of a RC factory Honda Works bike crank.....I believe Rick Johnson really liked this crank as did alot of other factory riders.

Which button allows you to upload pics

Motorrad

  • Guest
Re: HRC Works bike crank
« Reply #1 on: October 09, 2013, 12:57:15 AM »
is it any of these parts?

sandblaster can give you a tutorial on peektures.

here is a fun site. (poke around the factory parts)

http://www.mxworksbike.com/parts%20a.htm

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: HRC Works bike crank
« Reply #2 on: October 09, 2013, 02:37:44 AM »
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline PJSMAN

  • Jr. Member
  • **
  • Posts: 24
Re: HRC Works bike crank
« Reply #3 on: October 09, 2013, 11:03:04 AM »

Offline PJSMAN

  • Jr. Member
  • **
  • Posts: 24
Re: HRC Works bike crank
« Reply #4 on: October 09, 2013, 11:29:56 AM »

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: HRC Works bike crank
« Reply #5 on: October 09, 2013, 12:05:22 PM »




This is the HRC RC500 snap-ring crankshaft that is talked about in my book "Legendary Motocross Bikes." These cranks are tunable for different power-band characteristic's by altering the rotating inertia. Steel, tungsten and nylon inserts were available and gave the tuner the flexibility to adjust the power-band simply by changing the weights. The process to change the weights is very simple as they are held in by snap-rings located in the crank flywheels. This along with all the other available options that HRC offered, made the RC500's some of the most competitive motocross bikes ever produced. Ask any factory Honda rider that ever used one of these crankshafts and he will tell you this was the biggest improvement on the bike. Even though the crank flywheels look like they are made from billet, they are actually made from several machined pieces that are hollow in strategic areas and then electro laser welded together. Very few of these were made and the cost was well over $10,000.00 in 1980's dollars.
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline PJSMAN

  • Jr. Member
  • **
  • Posts: 24
Re: HRC Works bike crank
« Reply #6 on: October 11, 2013, 09:47:57 PM »
Has anyone ever seen this done ....outside of Honda HRC ?

Offline mun

  • Full Member
  • ***
  • Posts: 58
Re: HRC Works bike crank
« Reply #7 on: October 12, 2013, 11:03:01 AM »
If you change the HRC crankshaft weights, you should split the engine.
If you do weights holes in the outer edge of the crankshaft, so you only need to take off the cylinder. Easy.
It's my 5 cents.

Bad picture, but you see the principle.

Offline RoostiusMaximus

  • Sr. Member
  • ****
  • Posts: 301
    • Millar Racing Engines
Re: HRC Works bike crank
« Reply #8 on: October 17, 2013, 09:57:58 AM »
hrc weights could be accessed in the ignition housing and clutch case  :wink:

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: HRC Works bike crank
« Reply #9 on: October 17, 2013, 12:31:19 PM »
hrc weights could be accessed in the ignition housing and clutch case  :wink:

Pipe plugs or freeze plugs?
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.