Author Topic: Looking into selling.....  (Read 5018 times)

0 Members and 2 Guests are viewing this topic.

Offline jbehunin

  • Full Member
  • ***
  • Posts: 50
Looking into selling.....
« on: October 15, 2013, 06:11:58 AM »
I am looking into selling my 1993 KX 500.

I bought this bike from an elderly rider that used it sparingly. When I bought the bike, it had been garaged for over 6 years. It was sitting so long that the rubber on the tires was hard and you could twist them and they would break off.

Anyways, when I got it home, I tore it down to the frame. I had Millennium Technologies re-nikasil plate the cylinder. I had the bottom end split open because of a cracked case. I was able to find cases from a 2003 KX 500 that were in perfect condition. I had all the seals and bearings replaced, and I also had a local ex Team Green mechanic modify the transmission and reassemble the bottom end for me.

I don't know how much this thing is worth, so I am asking all of you out there before I list it.

I have a bunch of other items that I will let go with the bike.

An over sized gas tank
Extra radiator shrouds
Extra 18" rear wheel
Extra 19" rear wheel
Extra front wheel
Extra swing arm
Extra front forks off of a '98 KX 500 with triple clamps
Stock exhaust pipe
Extra FMF Turbine core silencer
and a few other small extra items.

I am not sure how to post pictures here.....
« Last Edit: October 15, 2013, 06:32:32 AM by jbehunin »

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #1 on: October 15, 2013, 07:15:57 AM »
Here is a link showing how to post your pics:
http://www.kxriders.com/forums/index.php/topic,10040.0.html
If you can't figure it out, shoot me an email with the pics and I'll do it for you.
Kelly Blue Book full on hard core retail is 1575.
Trade in is 1020.
I usually tell local people that they will get somewhere in between..
However, you have a Big Bore 2 stroke in what sounds like excellent condition.
If you find the right buyer you could probably get 1575 for the bike (Parts not included).
The problem is a slumping economy, high unemployment or under employment, and when football season starts, the riding season nearly dies...
So, it really is a roll of the dice this time of the year.
If it were me and I wasn't hurting for the money right away I would sell the parts separately and wait till next spring to sell it.
Then again, you never know who is looking to buy right now and has cash...
If your going to sell the parts separately I might be interested in the Extra FMF Turbine core silencer  :-)
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline jbehunin

  • Full Member
  • ***
  • Posts: 50
Re: Looking into selling.....
« Reply #2 on: October 15, 2013, 09:15:36 AM »
I will sell the parts individually for sure. It just sits there. PM me if you're interested. Thanks!

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #3 on: October 15, 2013, 09:34:00 AM »
Here are some pics of the 1993 KX 500. The pic of the bike with white number plate backgrounds was last year. The pics with the yellow was last week.





The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline 81cr450

  • Hero Member
  • *****
  • Posts: 887
Re: Looking into selling.....
« Reply #4 on: October 15, 2013, 12:38:15 PM »
Dibs on a rear wheel prefer the 18"  but really all I care about is a the hub are either the 3 bearing

Should have r1237 on it not r1213

How if much if you have the right hub anyway Thanks
« Last Edit: October 15, 2013, 12:41:38 PM by 81cr450 »
if I only had a pair, I could actually ride this thing

& to the people I like  FYYFF

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #5 on: October 15, 2013, 12:48:14 PM »
Dibs on a rear wheel prefer the 18"  but really all I care about is a the hub are either the 3 bearing

Should have r1237 on it not r1213

How if much if you have the right hub anyway Thanks

Are you looking for the single or double drive bearing?
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline 81cr450

  • Hero Member
  • *****
  • Posts: 887
Re: Looking into selling.....
« Reply #6 on: October 15, 2013, 12:59:58 PM »
r1237

3 bearings total , I have the 2 bearing hub but plan on making some power & want the extra insurance
if I only had a pair, I could actually ride this thing

& to the people I like  FYYFF

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #7 on: October 15, 2013, 01:01:29 PM »
Ok, be careful because I have seen the single drive bearing on a r1237  :-o
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline 81cr450

  • Hero Member
  • *****
  • Posts: 887
Re: Looking into selling.....
« Reply #8 on: October 15, 2013, 01:04:47 PM »
d**n, it was your site I was looking up the interchange off of  :-D, glad you saved me

Have you seen 3 bearings in the r1213?
if I only had a pair, I could actually ride this thing

& to the people I like  FYYFF

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #9 on: October 15, 2013, 02:37:03 PM »
Nope...
Granted, I have only seen a single bearing on the newer hub once before so the odds should be low of finding another...
But ask first and you won't be sorry..
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.

Offline ELRUKO

  • Jr. Member
  • **
  • Posts: 34
Re: Looking into selling.....
« Reply #10 on: October 15, 2013, 04:29:12 PM »
MY 1993 had only single bearings.  Thats what I found out when it blew up...

Offline sandblaster

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8,271
    • OEM-CYCLE QUALITY USED PARTS
Re: Looking into selling.....
« Reply #11 on: October 15, 2013, 04:41:42 PM »
96 Was the last year of the single bearing.
The four stroke engine: That's one stroke for producing power and three for wearing the engine out.