| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
| 0 Members and 8 Guests are viewing this board. | ||||
|
|
1 Replies
1,625 Views |
August 15, 2014, 03:08:18 AMby sandblaster |
|
|
|
|
casting marks / stampings
Started by yeomans |
0 Replies
1,625 Views |
May 11, 2013, 05:46:30 AM by yeomans |
|
|
|
my rads are shot.Will any others fit?
Started by tunster |
1 Replies
1,626 Views |
November 19, 2009, 12:33:18 AM by drewh14 |
|
|
|
Conventional forks on newer KX500s
Started by Ramski |
0 Replies
1,626 Views |
May 27, 2005, 09:13:09 AM by Ramski |
|
|
|
could it be the dry side seal?
Started by reklessj |
0 Replies
1,627 Views |
October 07, 2012, 04:48:21 PM by reklessj |
|
|
|
Gnarly pipe
Started by Rotorised |
2 Replies
1,628 Views |
October 19, 2006, 12:17:19 AM by Rotorised |
|
|
|
HERES A SEAT COVER MADE IN NZ
Started by kiwimonster |
1 Replies
1,629 Views |
December 12, 2008, 04:29:15 PM by Murphy |
|
|
|
O ring chain's do last a LONG time
Started by Torch654 |
2 Replies
1,629 Views |
October 21, 2005, 01:27:09 AM by alan |
|
|
|
does anyone have a stock flywheel?
Started by kix500 |
1 Replies
1,629 Views |
April 26, 2006, 01:31:25 AM by gowen |
|
|
|
Stuck chain adjuster
Started by BigKX |
2 Replies
1,629 Views |
February 16, 2005, 06:41:15 AM by jdv500 |
|
|
|
Pivot Works or All Balls Bearings
Started by bigborefan |
1 Replies
1,630 Views |
March 28, 2005, 02:30:56 PM by hughes |
|
|
|
Thank God for Good People!
Started by stock500 |
3 Replies
1,631 Views |
October 05, 2008, 12:10:54 PM by maddoggy |
|
|
|
Kips valves question.
Started by IcemanK5 |
2 Replies
1,634 Views |
January 11, 2012, 02:42:50 AM by IcemanK5 |
|
|
|
Crank Seals ???
Started by KX Newfie |
2 Replies
1,634 Views |
October 17, 2008, 03:51:57 AM by KX Newfie |
|
|
|
5 Replies
1,634 Views |
May 21, 2010, 12:59:04 PM by kxpegger |
|
|
|
|
KX500 1989 frame
Started by Krulos |
1 Replies
1,634 Views |
December 27, 2010, 11:25:34 AM by Goat |
|
|
|
Lost swing arm nut again!
Started by Hick |
6 Replies
1,635 Views |
April 18, 2009, 05:34:03 PM by Hick |
|
|
|
A pipe fitment question
Started by puffy |
3 Replies
1,636 Views |
May 01, 2008, 11:43:43 PM by hughes |
|
|
|
cylinder porosity
Started by Foxx4Beaver |
3 Replies
1,636 Views |
March 09, 2012, 07:36:26 AM by Foxx4Beaver |
|
|
|
0 Replies
1,636 Views |
January 31, 2008, 01:26:08 AM by Hillclimb#42 |
|
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic