Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
| 0 Members and 7 Guests are viewing this board. | ||||
|
|
Is the piston considered bad when...
Started by ShanMan |
10 Replies
5,570 Views |
June 18, 2003, 02:57:33 AMby ShanMan |
|
|
|
Shimming KX500 fork springs
Started by ShanMan |
8 Replies
3,111 Views |
December 27, 2004, 02:50:02 PM by hughes |
|
|
|
Wide pegs for early years?
Started by ShanMan |
3 Replies
2,846 Views |
August 10, 2003, 04:40:45 AM by ShanMan |
|
|
|
installing a new base gasket
Started by ShanMan |
6 Replies
4,054 Views |
June 04, 2003, 06:03:41 PM by woodsy |
|
|
|
cylinder oil leak...is this normal?
Started by ShanMan |
4 Replies
3,489 Views |
April 25, 2003, 05:07:05 AM by ShanMan |
|
|
|
engine paint
Started by ShanMan |
0 Replies
2,696 Views |
June 04, 2003, 08:18:04 AM by ShanMan |
|
|
|
KX500 is a 5 speed...right???
Started by ShanMan |
2 Replies
3,044 Views |
March 17, 2003, 10:28:19 AM by ShanMan |
|
|
|
Stripped drain plug....best fix?
Started by ShanMan |
8 Replies
6,402 Views |
June 25, 2011, 05:17:57 AM by gwcrim |
|
|
|
dialing in the stock rear shock
Started by ShanMan |
10 Replies
4,479 Views |
September 30, 2003, 02:29:14 PM by HULKSTER |
|
|
|
Odd Miscue....could use help to diagnose
Started by ShanMan |
5 Replies
3,670 Views |
April 21, 2003, 03:27:23 PM by ShanMan |
|
|
|
Properly lubing clutch cable...how?
Started by ShanMan |
8 Replies
4,449 Views |
July 05, 2003, 04:03:48 AM by tomasaki |
|
|
|
more steering questions...
Started by ShanMan |
6 Replies
4,041 Views |
May 22, 2003, 05:10:09 AM by ShanMan |
|
|
|
status: broken arm, broken parts...fixed arm and new parts!
Started by ShanMan |
6 Replies
3,843 Views |
June 27, 2003, 08:22:14 AM by beastrider500 |
|
|
|
typical gearing for a desert/trail sled?
Started by ShanMan |
8 Replies
3,333 Views |
January 18, 2011, 02:05:26 PM by Purpletj |
|
|
|
Out with the old, in with the new (er)???
Started by ShanMan |
2 Replies
2,951 Views |
May 15, 2003, 04:28:31 PM by ShanMan |
|
|
|
KX500 Suspension setup
Started by ShanMan |
3 Replies
7,241 Views |
February 27, 2003, 07:18:38 AM by ShanMan |
|
|
|
if you run V-Force or RAD, do you need a reed spacer?
Started by ShanMan |
3 Replies
3,169 Views |
May 13, 2003, 09:15:55 AM by Paul |
|
|
|
Perch and lever transplant from a newer KX5 to my '87
Started by ShanMan |
5 Replies
3,761 Views |
April 01, 2003, 08:31:01 PM by mikesmith |
|
|
|
grafting '88-up plastic to a '87...is it doable???
Started by ShanMan |
9 Replies
3,333 Views |
September 18, 2007, 12:54:25 AM by hughes |
|
|
|
Best source for a reed spacer?
Started by ShanMan |
1 Replies
3,308 Views |
May 13, 2003, 05:00:01 AM by sdkx500 |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic